10651559101 Kenmore Refrigerator - Instructions

In our new house we found that one of the wire racks supporting a slide-out glass fridge shelf was broken. The cylindrical support rod at the back we unglued/unattached. I tried to fix it with super glue (came apart), and then metal epoxy (worked at first, but shelf collapsed under load). A new wire frame fixed it with zero tools. Problem solved! Note: I had problems matching the exact fridge model at first. I contacted Kitchenaid support and they sent a pdf with every part labeled. It was then easy to find the part on PartSelect. I appreciate the high quality images that let me confirm the match visually.

After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

Removed a total of 12 screws, unplugged the control boards, plugged-in the new control boards and replaced the 12 screws.The FAQs section of the PartSelect troubleshooting guide helped me correctly identify the control boards as the source of the problem. The LED sequence was the key to identifying the problem.

First, I went online and looked up the directions to remove the ice maker. After several attempts of removing and re-installing it, I found that one of the tines on the wheel had broken of making it impossible for the ice to dispense. I went online to PartSelect, found the exact part I needed, not the new replacement one either, and watched the proper installation directions on the website. When the part came, I did exactly what the video said, which took me maybe 10 minutes, and plugged the fridge back in - make sure you unplug the refrigerator - don't just shut it off!! I heard the water going into the maker, and about 30 minutes later I heard the first batch of ice fall into the bucket!!! It was music to my ears!!!! Oh, and by ordering from PartSelect and doing this simple repair myself, I saved $150.00!! PartSelect is now my new best friend!!!

Fridge would stop cooling, get way over temperature. I noticed it would start up again if I tapped near the thermostat. It would run for a while then stop again. Replaced the thermostat exactly as shown in video. Fridge works fine now.

all is fine now. thanks andy

I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.

watched the video followed the instructions and the repair took less than 30 mins. thank you parts plus for the video ref now workes properly and saved me a bundle of money

Remove icemaker, take off Icemaker control & motor ( 3 screws ) & install new part. Started making ice in less than 24 hours. Very happy customer.

I opened the box. That was the hardest part. I slid in the new drawer. I was a little distressed that my model # was not listed, but the pictures on your site were very helpful. Thanks

Was surprisingly easy. Hardest part was taking the cover off the front to get access to the control bracket and switches. Can be done by prying two notches on underside of cover until they pop. Then slide up and off. Once off I could immediately tell the plastic clips on control bracket were broken. So replacing fixed that issue. My other issue was the ice dispenser door would not stay closed and sealed. I noticed that the plastic hook that holds metal dispenser pin in place was broken. Had trouble finding that part online so I superglued it in place and that has held it just fine. Now both my ice dispenser and water dispenser are working after buying a $10 part. This site is awesome. I am sure I would have paid $200 for this from a repairman.

I was amazed how easy it was to replace this control board. I printed the pictures and instructions for the part that were on your site. There was a video for another part and it allowed me to get familiar with the layout of my unit. Thank you very much.

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

Remove drip pan from indoor ice dispensing system remove to bottom screws holding dispenser faceplate .lift faceplate out of the way exposing the bracket and ice and water dispenser micro switches be careful in removing microswitch, the one I removed came apart and had a little difficulty putting it back together ,used super glue and fix that problem. No instructions came with bracket so take your time. This is a relatively simple job any one should be able to do it.

My ice make had stopped working and I thought it was a water connection issue, however, after removing the motor cover, the plastic gear just fell to the floor. I wrote down the model number and looked the part up online. I ordered the part and it arrived a few days later. Three screws and a new motor and I had a working ice maker. Great experience.