10651552102 Kenmore Refrigerator - Instructions

Pretty simple, remove the old one and put in the new one - kinda alike the "Automotive Tech's" of today.

Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

Nothing to it, just slide the drawer in. Fast Delivery, Smooth Transaction, Great Service. I will use them for all the parts I need in the future. Thanks

removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

My wife could have made the repair, I got on line, typed the problem in and PartSelect came up. The drawings were there as well as instructions. The part came, again with instructions and it took about 20 min. Good job guys.

Shut off water & electric.Remove 2 screws,cut water lines,unplug electric plug. Install electric plug,push water lines in.reinstall screws,hook up water line & plug in ref.Turn water on, ck for leaks.

Took the old one out and put the new one in. No problem.

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Thermostat replacement

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

I pulled the broken drawer out. I removed the screw in the existing stud with a phillips screw driver. I replaced that stud with the one I ordered and the new screw that came with it and I slid in the new drawer. Very easy. In fact the most difficult part was finding this website, but I've book marked it just in case I need more parts in the future. Thanks for the clearly marked photos on the website so I knew exactly what to order and for the quick delivery of my parts!

The customer service people did some cross checking and found a shelf and drawer that would work in my fridge. It did!! I love it now!!!Thanks for your help I did have to remove one of the selves - but now I have an extra!