10651254104 Kenmore Refrigerator - Instructions

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Your directions were clear. When I took the control off the left side of the freezer compartment the resister burnt the plastic so badly that I had to pry cover loose. This may be a problem for others. Thanks from this "Do-it-yourselfer".

Removed and installed new control boards

Align new Ice Guide with two upper tab holes and push into place. Then push bottom tab into bottom hole until it snaps into place.

After receiving the Control Bracket from postal Service & followed directions as outlined in online Viedeo, the total installation was completed in 20 minutes. The last time that the Control Bracket ice switch was broken I had a Handiman install the new Bracket and the total cost was $115.58; this time the total cost was $21and I have one extre Control Bracket for future break down,

Just like in the video. Just snapped it in! Thanks

Removed refrig. door and replaced closing cam and tightened the bottom cam

Took ice maker main cover off. Took nut driver to remove wire cover. Unplug wiring. Slid out old unit. Put extra parts from old unit to new one required for my model. Slid new unit in.. Plugged in wiring. Installed wire covering.

I removed the on/off bail wire. I then removed the cap over the motor/control panel. I removed the 3 screws, lifted old unit out, installed new unit and then put everything back together. I had ice within 12 hours and it's run like a top since. I am a 64 y/o widow & I try to repair everything myself to save money. I'm very pleased with Part Select & will recommend them to everyone. Awesome shipping time too. Ordered on Thurs. Received on Fri. Fixed on Friday afternoon!

FOllowed the vedio instructions which made the installation very helpfull.

In our new house we found that one of the wire racks supporting a slide-out glass fridge shelf was broken. The cylindrical support rod at the back we unglued/unattached. I tried to fix it with super glue (came apart), and then metal epoxy (worked at first, but shelf collapsed under load). A new wire frame fixed it with zero tools. Problem solved! Note: I had problems matching the exact fridge model at first. I contacted Kitchenaid support and they sent a pdf with every part labeled. It was then easy to find the part on PartSelect. I appreciate the high quality images that let me confirm the match visually.

After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

Removed a total of 12 screws, unplugged the control boards, plugged-in the new control boards and replaced the 12 screws.The FAQs section of the PartSelect troubleshooting guide helped me correctly identify the control boards as the source of the problem. The LED sequence was the key to identifying the problem.

First, I went online and looked up the directions to remove the ice maker. After several attempts of removing and re-installing it, I found that one of the tines on the wheel had broken of making it impossible for the ice to dispense. I went online to PartSelect, found the exact part I needed, not the new replacement one either, and watched the proper installation directions on the website. When the part came, I did exactly what the video said, which took me maybe 10 minutes, and plugged the fridge back in - make sure you unplug the refrigerator - don't just shut it off!! I heard the water going into the maker, and about 30 minutes later I heard the first batch of ice fall into the bucket!!! It was music to my ears!!!! Oh, and by ordering from PartSelect and doing this simple repair myself, I saved $150.00!! PartSelect is now my new best friend!!!

Fridge would stop cooling, get way over temperature. I noticed it would start up again if I tapped near the thermostat. It would run for a while then stop again. Replaced the thermostat exactly as shown in video. Fridge works fine now.