10651112711 Kenmore Refrigerator - Instructions

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

Watched a video on how to disassemble the old bucket and reassemble the new one. Piece of cake. Thank you for the part and how to video.

Henry

Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company

Easy repair, third time in four months, same part. I don't recommend Whirlpool refer's. Stick to the washer and dryers.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

I added an icemaker kit. Everything I needed was in the kit. The refrigerator was presetup for an icemaker it was just never added. The only problem I had was that the holes for attaching the water solenoid were not pre drilled so I had to drill them myself and use sheet metal screws. The icemaker is working great.

First off you need to shut off the water supply valve that goes to the icemaker. Next pull the refrigerator from the wall , thats the fun part. I did not unplug my refrigerator when I did this . You can to be extra safe. At the bottom on the back side remove the cardboard cover on the bottom like four or five screws and set this aside. The water valve is on the bottom on the right side. There are 3 water lines attached to it. Having a towel handy might be helpfull. 1 line supplys the water, 1 is for the water dispenser and 1 is for the ice maker. These are push in connections no wrench needed. Remove the 2 screws that attach water valve to frame. Arrange it to make removing the 2 wire connections and water lines easier to remove. Wire connections just pull off. Mark them as to what valve they go to. Next remove the water lines. you need to remove a plastic lock that insures that the water lines do not pop off, very simple. Next push down on the nylon connector push down on the top of connector and pull on the plastic water line at the same time and it will come out. Do this to all 3 water lines. Remove old water valve and install new one in the reverse order. The water lines just push in no need to mess with connector when line is in reinsert the plastic lock. Reconnect the power connections. Align the water valve bracket with screw holes in frame and reattach the 2 screws holding it in place. Now would be a good time to turn on the water and check for leaks. You can check water dipenser but ice maker has a mind of its own. If all is good reinstall the cardboard cover on the back bottom and push refrigerator back where it was. Make sure the water line is not kinked. Aftre a couple of hours the ice maker should start making ice.