10650793001 Kenmore Refrigerator - Instructions

Installed two circuit boards which was very easy & within 30 minutes ice was being made

The water inlet valve was easy to replace. Just like the video shows. With one exception. I found the two metal brackets were tough to get apart because they were riveted together. So I took the drill with a 5/16 bit and drilled the rivet apart. It might have come apart without drilling but I was afraid of bending the brackets. You don't need to drill clear through both brackets. Just the clean the head of the rivet. It was quick and easy. The bit size is not important just so it is bigger than the rivet head.

If you have to push your door to close it and it doesn't close on its own, this is your fix. These door cams are two plastic pieces on the bottom hinge, one on the door and one on the bracket that goes to the body, that engage like a gear with only a couple of teeth. They are supposed to have raised teeth that engage to ride the door to a closed position when it is nearly closed. They are plastic and are made to wear down. To change, empty the door, then at the top of the door (i.e., looking down from above) unscrew two bolts that go to the hinge. The door then lifts off the bottom bracket. Put the door on a soft surface and unscrew the bolt that holds this cam. You can re-use the bolt. There is another cam bolted to the bracket that stays attached to the fridge. Change both cams at the same time. Reverse the process to re-install the door. Your door will close like new for under $10, in maybe 15-30 minutes.

Upon arrival I unpacked drawers and set in their location

take nutdriver remove back cover, remove screws holding valve, unhook lines, hook lines to new valve, reattach valve and bracket and cover . yhats it!

When the new crisper drawer arrived, I pulled out the old one and slid in the new one in less than 5 minutes. We won't overlead the new crisper drawer. Thank you PartSelect. I saved about $25.00 ordering this part from you.

removed the ice container, remove the two screws that hold in the shaft and seal. use pliers to remove worn out shaft, drop in the new shaft and seal reinstall the cover with the two screws and your done. took maybe 5 minutes start to finish.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Read the reviews on how to test if part was bad. It was! Ordered new infered sensors and watched your repair video! 2 hours later the ice maker was making ice:) Very easy! Thanks David

Completely disconnected the power. Just shutting off the ice maker switch does not shut off the power to these boards. The emitter and Receiver boards are located in the side panels of the freezer-one on the right and the other on the left. Just remove the 3 screws in each cover and disconnect the wire connectors and install the new boards. It's very straight forward and easy to do.

checked the close and open switch on front door first

from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

I watched a couple of videos on your website about how to install a couple of parts that could possibly be causing the problem. Then I went and took the cover off of the area where the ice and water dispenser are in the door. I could tell from watching the videos which parts to look at to see where the problem might be. I figured out which part it was because I could see where it was broken. I then ordered the part. After I received the part I watched the videos again and then did the repair. VOILA! It worked. I put everything back together and the water dispenser was working. I was so pleased that I didn't have to call a repair man and I actually fixed it myself! My husband was so glad too.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

I removed the old water inlet valve and replaced it with a new one. I had to cut the existing water lines with a razor to fit the new design of the new inlet valve. I also had to remove the inlet water valve and attach it to the new one. It was real easy once I reviewed the U tube video on how to replace the valve.