10650793001 Kenmore Refrigerator - Instructions

Insert lenses from left to right snap in

Remove the door on the icemaker. Remove a screw on the bottom right of the icemaker and remove the bracket. push two small tabs on the bottom to release icemaker and slide out. unclip plugs that are on the wire. To reinstall just do the reverse.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Followed instructions- removed and replaced with new water inlet valve also replaced control bracket. Now no leaks and plenty of ice thanks to partselect, the right part, the right price and fast delivery . Thank you

removed front trim, removed plastic bracket, removed broken ice guide, installed new ice guide, installed removed items in reverse order, finished.

removed the 3 screws from the receiver first, on hinge side with the flap The toughest part was twisting my arm around and upside down to plug the new board into the wire harness since it had very little slack and the wires were stiff from cold, the emitter on the opposite side was as easy, care needed to be taken with the upper screw partially hidden behind ice maker itself but it was an easy removal. Again, short wires and stiff from cold make alignment of the plug to the board just bit awkward to ensure it was seated properly. 15 mins later I heard the first emptying of the ice maker

Remove 3 screws on the emitter and 3 screws on the receiver. Removed the plugs and reinstalled the parts. Very simple and easy. Ice is flowing again.

Researched in "ehow" the procedure. Looked relatively simple so I ordered the part. When it arrived, emptied the frig, pulled it out, thawed out the auto ice maker with a hair dryer. I then examined the old part and compared it to the new part. They were close. Old part had a rivet attaching it to another bracket which had a primary valve that led to the filter cartridge housing. I had to drill out the rivet to seperate the mounting brackets. The electrical connectors were rear facing on the old unit and front facing on the new unit. Not a big problem, just concerned that the solenoid leads might be polarity specific. I called my brother who works on restaurant equipment and he said that as long as the long were the same color, polarity was not an issue. He was right. The second concern I had was that the plastic line from the primary input valve was a stiffer gray plastic line with a rib molded on the ended to secure a metal compression nut. I wondered again if that would cause a problem with the new pressure connector. It did not. Just cut off the rid and slide it in. Frig is working great, dispensing water and ice like it was new. Bought the frig for $1,000 13 years ago, now sells for $2,500. Save a ton of money by buying the part and doing it myself. Thanks.

Just remove old one which was really easy since it was practically falling off and replace with new one. It is a bit tricky because you are afraid of breaking the new one. Watch the video and you will be more confident. I was REALLY impressed with the shipping. I ordered on Monday afternoon and when I returned home Tuesday afternoon it was waiting for me on my porch , and this was the week between Christmas and New Year when everyone was fussing about not receiving packages. NOT ME!

Did exactly what the video showed . First I went through the test procedure to conferm my boards were bad . But ice maker didn't work after the control boards were replaced. I did some more research to find out what the problem now could be. I discovered where the water goes into the ice tray the line was frozen. Got the hair dryer out and melted the ice that had the water restricted. Been making ice every since. I tell everybody about (part select) web. Sight now

took out the old one and replaced with new. PERFECT FIT.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.