10650592000 Kenmore Refrigerator - Instructions

I watched the video so I had an idea of what to do. It was pretty straightforward. Turn off the water, take out the screws, line everything up, replace the part. It went smoothly and the icemaker is working again. :)

Door handle was in three parts. 1. Middle Part with two screws on each end. This is the part that snapped off. (2) Top 2 ft. strip that goes over the top of the middle part. (3) 2/1/2 ft. lower that goes over the lower screws, I slid the top part and the lower part off. exposing the middle Handle. I removed the two top and two bottom screws. and attached the New Part with the same screws..... slide the top and bottom pieces back on. "Piece of Cake" took about 5 min.... One point..... the NEW black handle, did not exactly match because of 10 years of solar fading on the older strips...... this can be fixed somewhat with an "Amoral" type of silicone liquid.

Unscrewed three screws, inserted new part, completed in less than 10 minutes and my icemaker works!!!! My icemaker did not work for 2 years and after spending $58, my icemaker was back in action.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

the part was very cheap and with the instructional video for replacement it was extremely easy to replace

Bracket pin that holds the water dispenser switch broke. Has to replace the whole bracket. Removed cover, unsnapped bracket, removed ice and water switches. Installed switches on new bracket, snapped in bracket, replaced cover. Ops check good. Very easy to do.

It was a easy enough repair. A little bit tough to press locks in to release hoses because lines were not long enough to pull out for under the refrigerator.

I still have the parts, which look great. My son completely emptied to ice bin, de-iced the unit, cleaned the coupling.... it works.

I had a problem with my ice dispenser not dispensing ice. The water worked fine but the ice side didn’t dispense ice. I watch the video on Parts Select.com and it was very helpful, but my model didn’t have screws to remove the front cover. At the bottom of the front cover was two indention where you could put a small tool and pry on it, I had to take a small pick tool and pry up on the front cover to pop it loose. You have to take something small like a pick tool because if you use something like a screwdriver or a butter knife you will get behind the plastic housing (also called a hood) that is screwed to the refrigerator. The key is to remove the face plate from the plastic hood piece (that is screwed to the refrigerator), so you have to get in between the face plate and the plastic housing. If you get behind the plastic housing you can break the housing, you must get between the two pieces and it will pop loose. This is the only problem I had with this installation. The rest of the repair was very easy and now my ice maker dispenses ice great.

Took old one out put new one in and its like new! Costs for a simple drawer was $75! Expensive but the transaction was simple!

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

used the video on your web site. also read the overview made things really simple

I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.