10650584000 Kenmore Refrigerator - Instructions

The online video shortened the learning curve, and the cut the repair time in half.

Removed and replaced retaining clip and installed a new strain relief. Parts arrived in 2 days from the time they were ordered. No problems whats-so-ever. Great doing business with Parts Select again.

Order at 2:30 PM on Tuesday and had it by 1:30PM Wednesday. Less than a day on the delivery order. Thanks!

I saw the video online and followed the easy pop in directions by pulling the open tab away from the door notch then snapping it on-fast and easy.

I bought the part from Part Select and they sent a video on how to install part.

Put part on /did not see warter come at first had to go a cycal then ice again thanks alot, danny repair guy whanted 46$ to look at part. Good job.

My ice maker has been broken since august 2011. I called my son in law, which is very handy, he looked at the broken ice maker, said he had no clue how to fix it, since its computerized. Searched the internet, found part select website, watched videos, read customers feed back, based on information provided, ordered icemaker control and motor assembly (less than $60. 00), Called my son in law, in less than 10 minutes, part was installed. The next morning the ice bin was full. I am so greatful for your website, and my wonderful son in law.

The video on the website on replacing the Icemaker Assembly is great. I watched it then performed the R&R. It would have taken less than 15 mins but I took the time to clean the components which were reused. The water receiver on the new assembly is taller than the original. Luckily the water outlet in the freezer is rubber so I was able to bend it out of the way so I could slide in the new unit. The wiring plug in the new assembly was installed in reverse of the old one so I had to pull the unit back out, turn the wiring plug upside down, put it back in place then re-install the unit. Had a couple minor changes to make but the video is a great teacher.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

I followed the steps in the video posted on webpage describing the part. I watched a sement, performed the steps, and then watched the next segment. I spent more time trying to locate my nut driver set then I spent doing the actual repair.

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

I pulled the broken drawer out. I removed the screw in the existing stud with a phillips screw driver. I replaced that stud with the one I ordered and the new screw that came with it and I slid in the new drawer. Very easy. In fact the most difficult part was finding this website, but I've book marked it just in case I need more parts in the future. Thanks for the clearly marked photos on the website so I knew exactly what to order and for the quick delivery of my parts!

The customer service people did some cross checking and found a shelf and drawer that would work in my fridge. It did!! I love it now!!!Thanks for your help I did have to remove one of the selves - but now I have an extra!

simple remove and replace