10650512001 Kenmore Refrigerator - Instructions

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

I followed the UTube video step by step, pausing at each section made repair very easy. Watching the video is a definite must!

Simply done !

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

snapped in new bins.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

Spent six hours melting the ice berg, twenty minutes cleaning things up and ten minutes replacing the ice maker. The video was great the only piece of information that was missing was a statement that it may that several hours for ice to be produced. Thanks for the prompt and courteous support during ordering, a good product and support video.

I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

Easy repair, just snapped the old bins out and put the new ones in. It took longer to empty the old bins and fill the new ones. Customer service was excellent, also my order was to me in 2 days. Great service. Thanks PartSelect

I looked at the video that part select send. I did exactly what it said to do,and now my refrigerator is working just great. And the noise is gone. I thank you so much for your help. And I'm a 64 year old women thats how easy it was.

It was wonderful. I struggled with the old ones taping them and repairing them until it just didn't work anymore. Within two days they were here and problem solved. What a relief.

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

I can tell you they had the tray to my house within 3 days!! AM I IMPRESSED! Also they were a lot cheaper than ordering the same part from the major store where I bought the fridge. Thanks!

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.