10650456900 Kenmore Refrigerator - Instructions

I followed the easy to follow video instructions posted on the same web page I used to order the icemaker. I chose to order the complete icemaker rather than the motor assembly because based on price, ease of installation, and the chance something else could fail in the icemaker unit I preferred to order and install the complete assembly. PartSelect was a great web site to use to purchase appliance parts and get instructions. Didn't think companies did this any more. Great!

watched video, moved all wifes crap in freezer, replaced. Done, maybe 15 minutes total.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

Hi, this was an easy repair job. And, after I was done I felt like McGyver. It took me about 1 hour. The hardest part was getting ice maker's power source disconnected. That was tricky; you have to remove the housing that covers the power connector.

I rearranged the other bins on my refrigerator door. I checked the space between the bins, to make sure I could remove and insert items easily. I put my new bin in place, I made sure it was secure and I put taller items in the new bin.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

used the video on your web site. also read the overview made things really simple

I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

Used the trouble shooting off of YouTube and after finding that the heater was not at the right resistance, ordered a new ice-maker and installed. Very simple and a lot cheaper than going through Sears.

Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

Turn ice maker control off,hold up front cover remove two screws, remove cover, remove rear screw on the back right side, slide unit part way out, make sure flipper on left is out of the way, unplug connector on right, remove unit,remove bottom cover & put on new unit,install in reverse order, turn ice maker control on, done

I went on line and found your web sight. There was a list of the parts by number and I clicked on the rilght one. It brought up a video for repairing it myself. It was so simple. I just followed your instructions and within an hour I had ice. It makes so much ice I'm going to have to give it away. No really its great.

I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!