10650453902 Kenmore Refrigerator - Instructions

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

used the video on your web site. also read the overview made things really simple

I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.

Just snapped it in place

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Remove ice unit to take out ice. Remove both boards and replace.Had to unplug refig to thaw out water line because it froze when unit would not make ice.

Removed refrig. door and replaced closing cam and tightened the bottom cam