10650443901 Kenmore Refrigerator - Instructions

Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Watched the video and realized how easy it really was....followed directions and completed repair in less than 5 min....only issue Fed Ex lost original order....parts person was great...overnighted me a replacement

I started by viewing the video online showing how to make the repair. I then unplugged the fridge, taped the cover of the icemaker up out of the way. It was then a matter of removing three screws on both the emitter and receiver sides of the freezer and two screws each to remove the boards. I uplugged the modular plugs from each board and then reversed the proceedure. Icemaker is now working like new.

removed door and replaced the two parts

All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.

Removed the door, removed the old lower door cam, and replaced with new cam.

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

Opened freezer section of refergerator and taped Ice Maker cover door in the open position to remove emitter and receiver boards. Unscrewed the phillips head screws that secure the emitter board housing to the refrigerator side wall. Turned off power to the refrigerator and unpluged the emitter, removed the 2 screws that hold the emitter board against the housing and removed it, then I installed the new emitter board in the housing by screwing it in place. Repeated same process for removal and replacement of the receiver board. The whole process took me about 10 minuets.

I discovered the coupler was broken, so I went online to search for a repair. I found the part number for the coupler and washer. I used the short online video that shows step by step how to fix it. It was very easy and now the ice maker dispenses ice again! I researched Sears and your site, and your site with shipping was less expense than Sears. I called Sears and they didn't have the part in stock anywhere close to where I live to pick up, so with their price and shipping, your site was just a couple dollars cheaper. I receive the part very quickly after ordering.

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

i talked to a gentlman name Ruben and directed me to the parts i needed i ordered them and put them by myself i ended up saving over 200.00 dollars thanks to Select parts the minute i finished the process and closed the freezer doors i could hear the ice is comin down again it was good feeling. After i changed the emitter and the receiver this year every thing is working again

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.