10650292010 Kenmore Refrigerator - Instructions

I was amazed how easy it was to replace this control board. I printed the pictures and instructions for the part that were on your site. There was a video for another part and it allowed me to get familiar with the layout of my unit. Thank you very much.

The plastic "wiper" attached to the bottom of the ice "auger" in the ice dispenser unit broke. (It was made from a plastic that was not up to the freezing temps and heavy ice loads it had to move.) The new unit seemed to be of a different type of nylon/plastic. Problem was that the small machine screw at the bottom of the auger assembly could not be removed because of corrosion. I had to drill it out. Choices then were to purchase a new auger for about 60 bucks or reassemble the unit with a new 6-32 machine screw. There will not be enough metal left to allow it to be tapped so simply clean it out well and glue in the new screw with JB Weld. Allow to cure over night and you're back in business. Ours works fine so far. Good luck!

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

very easy in about 2 minutes. snap the old out and slap the new in

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Ordered replacement parts from Parts Select on Sunday and the parts were delivered to my home on Wednesday . Could not be happier with this company. It was very easy to see exactly what I needed from the diagrams they provide on the website . Parts arrived and were installed in just a few minutes. I would, and have recommended Parts Select to my friends ... AWESOME !!

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

There were excellent entries on the net of how to diagnose problem. Parts Select website had an excellent video on how to change part. Just followed instructions and changed parts in about 15 minutes. I am usually a klutz, but this was so easy

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

Replaced the Electronic control boards first, emitter and receiver, and that did not fix the problem. I then order the Control board/motor assembly in the ice maker, this did fix the problem and after a couple of hours I had ice. The repair was easy and the videos on the web site show you step by step.

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

We wanted an additonal shelf on the door of our 10 year old refrigerator. I called because I wasn't sure what to order. The saleswoman was very helpful and friendly and my order was placed quickly. It arrived in just a few days and was easy to place on the door. It is now in my refrig holding lots of little jars and bottles. Thanks PartSelect! We wonder why it took us so long to think to order this!

Swapped out the emitter and receiver control boards. Super easy. Watched the video on how to do it on your website.