10650273010 Kenmore Refrigerator - Instructions

Took the new chut set it into the ice dispensing openening,then cliped in place,End of repair.

read instructions from your site my wife repair refrigerator before i got home

Pulled out the old one an put the new one in. I was impressed with how easy it was to work with partselect.com, I had alway ordered through Sears before, but from now on I will be using partselct.com for ordering parts. Got the part in two days with free shipping and $20 les than Sears that did not have the part in stock.

SUPER EASY!!!! I pulled the old one out and put the new one in. Perfect fit and it took less than 60 seconds. This web site was about $30 cheaper than ordering from Kenmore and it was identical. I ordered my Crisper Pan on Wednesday and got it Friday. Highly recommended!!!!!!!!!

As your video showed. Used kitchen knife to get connection tight

Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.

Turn off water supply then Remove the dispencer trim by putting a flat screw driver into the slots at ths lower edge of trim and push down on trim as you pry the trim out and remove trim. Remove two screws holding the controls and unhook the far right connector and push to the side to get to old line,unhook the connecter at the bottom of door and remove compression nut from old line,remove the screw holding the old line in place and remove the assembly by pulling up and out. install new metal holder into slot and install screw to hold in place (If you have old style)cut new line at angle (Don't cut but about 1/2 inch off) and push new line down through hole at the bottom of the door where old one was and install the upper end into new metal bracket notch ,reinstall control panel with the two screws that were removed making sure that the controls strike the switches correctly ,reinstall the trim ,cut off the line to the match the connector and install the compression nut and put lines together,turn on water and check for leaks. Test and remove air and job should be complete. (hardest part was getting the trim off with out breaking it, I looked close and found the notches on the bottom)

I started by viewing the video online showing how to make the repair. I then unplugged the fridge, taped the cover of the icemaker up out of the way. It was then a matter of removing three screws on both the emitter and receiver sides of the freezer and two screws each to remove the boards. I uplugged the modular plugs from each board and then reversed the proceedure. Icemaker is now working like new.

My son took a plastic panel off the top front of the refrigerator. He found what looked like a four by four mother board type part. After looking at it he seen there was a part on it that definetly looked burnt.I got on the internet and did a search and found your site. I took a shot in the dark that this was what was wrong, looked up the part and ordered it. I had the part in two days. He installed it and BINGO, the refrigerator now works fine. Thank-you for all of your help and fastness on the delivery of the part! :) AWESOME!!!!!!!

old drawer out - new drawer in how easy can it get????

Remove the ice bin and dump ice. Remove the screw and replace the coupling and screw. Then I had to order a new motor shaft and replace it. Removed the cover and two screws with a nut driver , pull out the old shaft and replaced it with the new shaft. Put the cover on with two screws, place the ice bin on and had ice in about 30 mins. Piece of cake.

After replacing the cupling, I had to replace the shaft to the motor. Removed the two screws wirh a nut driver ,remoced cover, pulled the worn shaft out , replaced with new shaft, replaced cover with two screws. Works good as new.

removed door and replaced the two parts

All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.

Removed the door, removed the old lower door cam, and replaced with new cam.