10648567890 Kenmore Refrigerator - Instructions

Using a pair of pliers position the nose perpendicular to the inner wall of the ref and grip tight on the flat part of the support stud and twist counterclockwise until it become loose. Once loosened pull the support stud outward until it clears the the hole. Installation: Slide the support stud in and twist it hand tight. Using a vise grip and locking the jaw just tight enough to hold it firm on the flat parallel edges twist them (one at time) clockwise until it feels tight the tongues are parallel to to be able to slide the shelf support.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

The part fit perfectly. All I had to do was slide it in. Very speedy delivery and I am very satisfied with the service and would recommend your wedsite to anyone. Marie

replaced cam, new one broke after opening door 3 times...

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

A You Tube video described the repair steps and by following these instructions the whole process worked seamlessly.

ordered new replaced the old just slid in.

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

The door stop was completely bent over to the inside, preventing closure. Wife complained of door not closing by itself previously. I ordered the stop and closing cam kit.The door was easily removed after taking all food out of the door and removing the top hinge (3 screws using small socket wrench). Since the door has a magnetic seal, the door will not fall or move after this hinge is removed making the removal and installation quite easy. The door is light and was easily removed by lifting up off the bottom hinge. Once this is off, only a few screws needed to be removed to take off the door stop and cam. 2 screws hold the door stop and two screws hold the two cam pieces in place. The only difficulty was determining which of the several cams actually go on the bottom hinge. Make sure the one with the indented ring is used to go over the flanged door hole. This model did not use the cams with the flat surface or the one with the door hinge hole insert. This was a little confusing, not having the shop manual for this refrigerator. There seem to be more parts left over than those actually used. The instructions could have identified the uses a little better showing the optional models. Once everything is attached the door easily went over the bottom hinge and the door seal held the door in place while attaching the top hinge. Since this was the first time I attempted this repair, it took me a little longer to adjusting the door with the top hinge slightly loose to find the sweet spot where the door gently closes itself with total seal contact. If it breaks again, this repair shouldn't take any longer that 15 minutes.

It was this simple. I removed the old drawer and slid the new one in place. I was simply amazed at how quickly I received the part. I ordered it on the 24th of July and received it on the26th.

Simply removed the old drawer and inserted the new drawer. I ordered on Monday and the part arrived on Tuesday without paying for overnight delivery. What a pleasant surprise!!!

We suspected the thermostat assembly was the problem. We reviewed the video provided by PartSelect and accessed the thermostat assembly. To ensure the thermostat assembly was likely the culprit, we used a multimeter to test it. We ordered the assembly from PartSelect and were pleasantly surprised at the speedy delivery. Using the same video, we replaced the assembly and put the refrigerator back together. Thank you so much for saving us money we didn't have for the repairman. We will be ordering again soon to repair a leaky waterline and ice maker.