10648064894 Kenmore Refrigerator - Instructions

I followed the video instruction to a tee. It's exactly as described. However . . . my old plastic cam was so worn out that it had mushroomed within the inside of the door and would not come out without some "coaxing". And of all times to be unable to locate my needle-nose pliers, this was just plain bad timing. The cam was removed in pieces with the aid of a razor knife and a regular pliers. It took some additional time (approx. 1/2 hr.), but eventually it came out. Once this happened, the rest was a breeze. Moral to the story: Replace the cams on these doors every 5 or 6 years, whether it's needed or not. An ounce of prevention is worth 30 pounds of cure and avoided frustration. And for the few dollars spent on the cam, it just doesn't make sense not to.

I just followed the enclosed instructions

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

Once I determined easier access to the fan motor, I removed the three fan motor screws that held the motor on place. After removing the motor I remove the fan blade assembly held by one nut and reattached to the new motor. I then reattached the new motor with 3 new screws which were provide and reattached the power cord with the cord clip and began reassembling the icemaker housing, then moved the unit back in place which was installed under counter. I could do this repair in less than 45 minutes now that I have done it once. I saved several hundred $ from the original estimate and the parts were delivered in 2 days after I ordered online. This is definitely a DIY project!!

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

1. Unplug the refrigerator. 2. Remove the back cover at the bottom of the refrigerator. 3. Remove the two screws holding the vertical black bracket the fan is mounted to. This allows the bracket to move easily. The bracket does not have to be removed. 4. Removed the four screws holding the fan bracket to the vertical bracket. 5. Unplug the power connector from the fan motor. 6. Remove the entire fan bracket assembly from the refrigerator. 7. Remove the 4 screws holding the fan motor to the fan motor bracket and unmount the fan motor. 8. Remove the nut holding the fan blade to the fan motor and remove the fan blade. 9. Reverse the process, mounting the fan blade to the new motor, screw the motor to the bracket, screw the bracket to the vertical bracket, screw the vertical bracket to the refrigerator and plug the power connector back into the motor. I did not have to use any of the extra mounting hardware or electrical hardware provided with the kit. It might be a good idea to purchase a new fan blade with the motor kit, the fan blade can get pretty grungy. I cleaned the fan blade with some degreaser before remounting it.

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...