10646022801 Kenmore Refrigerator - Instructions

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice with fingers!

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

Replacement of parts was simple. But there are three main reasons that ice maker quits: door sensors stop working; ice maker, or it control system, stop working, or the coil controlling when water is released into the ice maker stops working. It was easy to replace the door senors; repairman replaced the ice maker and control board, which is located in one end of ice maker, but it ended up being the coil or simply a frozen water outlet into the ice maker that stopped the system from from working. The first thing you should do is to make sure that the water outlet into the icemaker is not frozen - use a hair dryer to melt frozen ice in the outlet - don't melt the plastic outlet with high heat. If the system still does not work go to this: look at red sensor on door to the the right. If it blinks twice in a couple of second with a time out and then repeats over and over, close the door on the receiving sensor on the left hand side of the casing and if the red light comes on steady then the sensor is working properly. So, now you have the coil that turns the water on and off or the water maker itself that can be bad. It will be one of these that are at fault, but not both. Call a repairman.

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.

PartSelect found and shipped the part quickly and with low postage directly to my door. I didn't have to worry about not being at home to accept the part and having to make a trip to the post office with a yellow slip.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Removed the Wiring & Troubleshooting instructions from behind the front Grill and used to troubleshoot the KSCS25IN side by side refrigerator. I then removed the three screws from the Emitter assembly on the left side of the freezer. Then disconnected the four pin connector. Removed screw holding emitter PCB to housing and replaced with the new PCB and then re-installed. Similar steps for the Receiver assembly and PCB on the right side of the freezer. Unit started making ice after making some water level adjustments on the Timer assembly.

I first had a technician come out to the house and he wanted to charge nearly $300 to replace the icemaker unit. I told him he was "high" and began doing my own research of the problem. That's when I found this website (thank God!) and read the notes from other customers. I figured out the secret location of the KitchenAid icemaker troubleshooting guide (why they hide this information I have no idea -- it's ridiculous), and performed the diagnostics to determine the exact problem. That is how I discovered that the emitter and receiver control boards were bad and not the icemaker motor module as the technician had tried to tell me. Good thing I didn't pay him, because my icemaker still wouldn't be working! The electronic control boards are a piece of cake to replace -- just 3 screws on each. Be careful with the electronical connectors since they snap in - don't pull on the wires, first unhook the snaps holding the wire connector to the board and then disconnet it. Once I replaced the boards I turned my refrigerator back on and immediately I heard the water running to fill up the icemaker and not much later I heard my first piece of ice hit the bucket. Woohooo!!!! It feels nice to fix a problem myself for a reasonable price. This site rules. I'll be coming here again in the future!!!

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

Very simple fix, remove 3 screws, two connectors to the old switch

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.