Models > 10644422603 > Instructions

10644422603 Kenmore Refrigerator - Instructions

All installation instructions for 10644422603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644422603
556-570 of 607
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

rocker switch broke off

  • Customer: STANLEY from OAKLAND NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Condenser Fan quite

  • Customer: Jennifer from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.

Ice Maker Not Making Ice

  • Customer: Gail E. from Palm Harbor FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The part arrived very quickly. I set up the laptop computer on the counter and started the instruction video (THEY ARE THE BEST!). With just a few starts and stops of the video during the installation in less than 15 minutes the repair was complete! The next day I had more ice than I needed. What a fabulous way to make appliance repairs at minimal cost! I will ALWAYS use PartSelect for any future repairs. I should also tell you that a 70 year old Woman did this repair - easily! If I can do it so can you!!

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

No Ice

  • Customer: James M from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Ice maker unit

ice maker not working

  • Customer: Guy from Palmdale CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the two circuit boards

Fan became noisy and started wobbling.

  • Customer: James from Cave Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Ice maker not making ice.

  • Customer: John from Greeley CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced emitter and receiver boards. That did not fix the problem, ordered valve hope that is it.

Condenser Fan was making noise

  • Customer: Kerry from Franklin TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Condenser fan vibrated loudly while turning

  • Customer: Robert from Aurora IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

Ice maker not working

  • Customer: Harry from Colonial Beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As your video showed. Used kitchen knife to get connection tight

Water would not flow into icemaker and icemaker would not work.

  • Customer: Kenneth from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions given by your demonstration. I took the back screw off, dropped the wire plastic cover. I then used the screwdriver to push the two (2)slots in and pulled the icemaker out and then unplugged it. I believe unplugging it was a little hard because the plug was pretty well sealed together and frozen. After finally getting the plug apart I then pulled the icemaker fully out. After pulling the cover off and putting it on the new one per your demonstration, I then inserted it back in. I stuck my hand behind the icemaker and bent the hose with my index finger and thumb so that it would drop into the water tray and then slid the icemaker back in until it snapped back in the slots. I then put the plug cover back on and reinserted the screw. I forgot to mention taking the front cover off before removing the icemake and reinserting it after replacing the icemaker. I would highly suggest customers follow your demonstration, it paid off well. I watched it about 8 times before I received the icemaker in the mail. Oh by the way water started flowing into the icemaker with 4 minutes and ice started coming out in about 30 minutes. As the icemaker got colder it started producing the ice faster. It's a sweet sound hearing the ice drop into the container.

noise coming from back of refrigerator. determined it was the fan

  • Customer: BRUCE from SOUTH WINDSOR CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Old fan housing broke

  • Customer: Michael from Pinedale WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

water dripping from spout

  • Customer: Terry from Union Star MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off water supply then Remove the dispencer trim by putting a flat screw driver into the slots at ths lower edge of trim and push down on trim as you pry the trim out and remove trim. Remove two screws holding the controls and unhook the far right connector and push to the side to get to old line,unhook the connecter at the bottom of door and remove compression nut from old line,remove the screw holding the old line in place and remove the assembly by pulling up and out. install new metal holder into slot and install screw to hold in place (If you have old style)cut new line at angle (Don't cut but about 1/2 inch off) and push new line down through hole at the bottom of the door where old one was and install the upper end into new metal bracket notch ,reinstall control panel with the two screws that were removed making sure that the controls strike the switches correctly ,reinstall the trim ,cut off the line to the match the connector and install the compression nut and put lines together,turn on water and check for leaks. Test and remove air and job should be complete. (hardest part was getting the trim off with out breaking it, I looked close and found the notches on the bottom)
All Instructions for the 10644422603
556-570 of 607