Models > 10644323400 > Instructions

10644323400 Kenmore Refrigerator - Instructions

All installation instructions for 10644323400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644323400
1,021-1,035 of 1,129
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken pan side track.

  • Customer: James from MARIETTA GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the bad ones off and put the new ones on. Childs play.

both drawer brackets broke, too much weight

  • Customer: craig from Camas WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced snap in brackets

One of the pan slide tracks got stuck during insertion

  • Customer: Alexander from Williamsville NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered two Whirlpool pan slide tracks, which are identical for the right and left sides. The first track popped right in, just like in the installation video, but the other one got stuck during insertion. I noticed that all three plastic tabs of the track were caught on the edges of their respective metal slots, and the plastic was being shredded by the metal when I pushed harder trying to insert the track. I took a kitchen knife and shaved off small slivers of plastic from the areas of the tabs that were catching. After that, the slide could be inserted easily.

Replaced the drive gear on the ice dispenser

  • Customer: Jeffrey from Rockford IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video on replacing this part was spot on. The screw was a little difficult to remove at first. It had been installed ten years earlier and also had some thread lock installed. A light swat with a hammer on the end of screw driver as I was trying to remove it got the screw started without stripping the Phillips head. Once we got by that little snag, it's a piece of cake, or piece of ice if you prefer.

Electronic Control Boards - Emitter and Receiver has no power

  • Customer: Tom from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
when I install the Electronic Control Boards has not Receiver the Electronic from water valve .

door made clacking , thunking noise when opened

  • Customer: BILL from ADVANCE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

Door would not close properly

  • Customer: George from Loudon TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions on line suggested I buy a lower door closing cam and a thimble top which I did. When I went to install I noticed that the door hinge with cam was also warn down. I had to again place an order and again remove the door to install. I would suggest those having this problem that they look at the hinge with cam also before ordering.

Outside door water shut off return part broken.

  • Customer: Jerome from Abingdon MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used 1/4 inch nut driver with swivel to remove the part retaining screw. Held new part into place and installed the retaining screw. Challenge was not hitting the level and putting water on me and the floor during installation. Relatively easy installation as long as you have patients.

Ice dispensor door would not close, dripped water, frosted inside freezer

  • Customer: Gail from Palos Heights IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Google refrigerator Model #, found your site, saw parts diagram right away, clicked on part 'Ice Door Kit', noticed your video on how to do repair yourself, showed it to my husband, ordered part, and it arrived the next day. That was the hardest part of the whole repair. I have been without use of the ice dispenser for about 9 months - took 20 minutes from opening box to getting ice again and saved myself a whole lot of money. I am one happy camper!!!

Ice dispenser door hinge inop

  • Customer: Robert from Emory TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Ice maker would not disperse cubes through the door

  • Customer: Danny from Fulton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Looked at drawing to see what sequence the parts went.

Install new flipper. Old one missing

  • Customer: Wells from Hereford AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove 3 phillips head screws with #2 phillips screwdriver. 2. Gently pull mounting bracket outward from freezer case. 3. Using fine needle nose pliers remove clip washer from lower end of flipper mounting rod. 4. Note position of flipper spring and pull mounting rod upward far enough to insert downward through new flipper and spring. 5. Install clip washer removed in step 2. Position assembly onto freezer cabinet and secure with screws removed in step 1.

ICE maker door hinge replacement

  • Customer: Theresa from Eagle River AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed two hex head screws, installed new part with nut driver for two hex head screws , very easy. I broke the tab off the hinge for the ice maker door when I installed a new ice maker the week before.

Bottom tab of ice guide broke.

  • Customer: David from Geneva NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used flat blade screwdriver to remove old guide by spreading the remaining top tabs. Inserted new guide and tipped the top forward to line up bottom tab in slot. Used screwdriver to push in tab. Once it was seated pressing in the top snapped the guide into place easily.
All Instructions for the 10644323400
1,021-1,035 of 1,129