10644273600 Kenmore Refrigerator - Instructions

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

pulled door off like video showed and undid the small bolts holding cams on and put new on. It was real easy. Thanks for youtube video

Pulled out old draw and inserted new one

First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.

Watched your video pull the door off switched parts and all done . Thanks to your web site it helped me diagnose and fix the problem

Be gentle when installing new plastic crisper drawer. If possible, read install instructions in Refrigerator Owner Booklet. Put new crisper drawer in position and gently push in until you are stopped by encountering the "stops" in side-support rails that are attached permanently to walls of refrigerator. Per Owner Booklet, lift new crisper drawer up slightly to pass over the "stops", then let the crisper drawer settle back down and push it in the rest of the way. Removal is reverse procedure. Be gentle!

If you have to push your door to close it and it doesn't close on its own, this is your fix. These door cams are two plastic pieces on the bottom hinge, one on the door and one on the bracket that goes to the body, that engage like a gear with only a couple of teeth. They are supposed to have raised teeth that engage to ride the door to a closed position when it is nearly closed. They are plastic and are made to wear down. To change, empty the door, then at the top of the door (i.e., looking down from above) unscrew two bolts that go to the hinge. The door then lifts off the bottom bracket. Put the door on a soft surface and unscrew the bolt that holds this cam. You can re-use the bolt. There is another cam bolted to the bracket that stays attached to the fridge. Change both cams at the same time. Reverse the process to re-install the door. Your door will close like new for under $10, in maybe 15-30 minutes.

Upon arrival I unpacked drawers and set in their location

When the new crisper drawer arrived, I pulled out the old one and slid in the new one in less than 5 minutes. We won't overlead the new crisper drawer. Thank you PartSelect. I saved about $25.00 ordering this part from you.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Removed cardboard, Removed 4 bracket mounting screws, Removed plug, Removed screws securing motor to bracket. . Installed new motor on bracket, Installed fan on motor shaft , installed new pigtail on motor, Installed new assembled motor and bracket, Hooked up pigtail to electric supply, Installed cardboard, Plugged in to power supply and Voila, not even one foul word during the whole process. Note: watch the factory video. Thanks.

I went on line to find the symptoms for what I was experiencing and went to web and entered the "KSRA" alphas and this list came up. I followed the explanation on video and it was identical. Good stuff.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Viewed the viedo - it showed what to do

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.