10644269600 Kenmore Refrigerator - Instructions

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Wash, dry, insert.

The Crisper Pan ordered through PartSelect was a perfect replacement. The item ordered arrived quicker than expected. I'm very pleased with your service.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

Ordered new glass shelf installed it.

Took the part out of the package and installed it. The service I received was excelent. Got the part two days after ordering it

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

Perfect fit. Slides smoothly. Arrived quickly. Thank you for a very easy web site.

Ordered the complete ice maker kit because I wasn't sure which part went bad. I replaced the ice maker assembly first which was very easy to do. I couldn't tell if the new ice maker was doing anything. I waited almost 16 hours before the ice maker started to run and make ice. I would just say to be patient after installing these parts if you don't immediatly see anything happening. Saving the solenoid and other extra parts if needed in the future.

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

Ordered part over the phone and received it two days later.....excellent service

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

Turn off power. Remove freezer shelves. Remove six screws on the back of the freezer. Slide out metal piece. Pop off plastic fan piece. Remove motor mount by squeezing metal bracket. Take off wires... Do reverse... Attach wires to new motor, install motor (may have to also use the clear rubber piece from the old motor which keeps the motor in place). Push fan blade back on. Screw in metal plate, turn on power. Good videos on YouTube as well.