Models > 10644269600 > Instructions

10644269600 Kenmore Refrigerator - Instructions

All installation instructions for 10644269600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644269600
31-45 of 422
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken light switch

  • Customer: Randy from Hays KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 16 of 26 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

Was not making ice and the filler tray was chipping material.

  • Customer: Robert from Hummelstown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 14 of 21 people found this instruction helpful
With a socket set and screw driver I removed the old ic e maker . It took about 1 hr. I worked slowly as not to make a mistake. The only part that gave me a problem was the plug. You need to take off the face cover to press down on the plastic release clip. Putting it back took half the time because you knew what to look for.Just plug it in and mount the screws back in place , make sure it was level and I had ice in about an hour.

overload relay switch/bad compressor--buzzing sound, ends with click, retries

  • Customer: Nathan from Garland TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 13 people found this instruction helpful
Remove back cover. Disconnect power. Pull out overload switch off compressor. Remove capacitor. The overload switch i ordered came with instructions. What took the most time was figuring out if i dared installing it the way i thought best. The instructions, in my instance, were incorrect. My overload switch didn't have a terminal #1. Long story short, i looked at the circuit diagram it came with, and based on process of elimination based on terminal sizes, I put it together. But the instructions weren't accurate. All in all for the average DIY, not a bad repair at all. I am still afraid that my problem is the compressor, b/c even after the new part is installed it still occasionally tries starting but can't, and keeps retrying until it does. It is either a faulty relay switch or a faulty compressor. We'll see which one wins.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The fan wasvery noisy.

  • Customer: Tracy from Coppers City Bottom WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Removed six screws from cover in the back of the freezer. Removed old fan . Removed power wires from old motor. Unclipped old motor from the mounting bracket. Replaced old motor and reversed the rest of the parts. Done

Orig Ice maker died

  • Customer: Al from Frankfort IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 9 of 10 people found this instruction helpful
I was able to salvage the existing wiring and simply replace the ice maker itself and the valve located at the bottom-rear of the frig.

Simply removed and replaced the screws, changed the water tube and connected everything back up. I probably spent more time cleaning behind the frig that replacing the parts.

Very pleased with how quickly the parts came and everything was included!

Refrigeator would not drfrost...

  • Customer: Curtis from Pikeville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 13 of 22 people found this instruction helpful
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Refrigerator door failing to close without being pushed shut

  • Customer: Kenneth from Greeley CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 10 people found this instruction helpful
Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.

CRISPER PAN SIDE REALES HAD CRACKED

  • Customer: LEVY from HOUSTON TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
I JUST SLID THE NEW PAN IN , PARTSELECT HAS THE CORRECT PART ALL THE TIME , I REPALCED MY ICE MAKER ONCE AND IT TOOK 15 MIN NO PROBLEM

freezer not cold, buzzing noise followed by a click then nothing from compressor, repeats every few minutes

  • Customer: ERIC from WYTHEVILLE VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Replaced the start relay, simple unplug old start relay and plug in of new one. Use care unplugging old one as it has 3 pins from the compressor that plugs into it and it must be carefully pryed loose with a flat screwdriver under it to prevent breaking one of them.

It was not coming out of defrost cycle

  • Customer: Dale from Flemingsburg KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 28 people found this instruction helpful
First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

Compresser would not kick in, it would click on and off.

  • Customer: terry from farmington MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
Unplugged the starter from compresser and put the new part in and all worked. Great service and I like the OEM parts not aftermarket. Will definately do service with you again. Thanks for making my life easier.

broken drawer

  • Customer: Jason from Farmland IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Put new drawer in fridge.

Fridge stopped working

  • Customer: Dan from Sumner WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 9 people found this instruction helpful
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

Cover Pan Crisper(bottom glass shelf and frame) were broken

  • Customer: anthony from ormond beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
New part slipped right into the studs and fit perfectly
All Instructions for the 10644269600
31-45 of 422