Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644102300 > Instructions

10644102300 Kenmore Refrigerator - Instructions

All installation instructions for 10644102300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644102300
571-585 of 766
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker broken.

  • Customer: Ken from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered the ice maker assembly..received it within 4 Days of ordering it.It took less than 15 minutes to install.Removed the screw that holds the wiring cover.pulled the old ice maker out.unhooked the wiring harness from the old one.unscrewed the bracket from the old ice maker installed it on the new one.Plugged the new ice maker in slid it in put the wire cover back on.It was making ice within 30 minutes. Thanks partselect.

I accidentally broke the arm that distributes the cubes to the ice bucket about a year ago. Just recently, the malfunction caused the entire thing to freeze up because the frozen cubes weren't cleared from the ice tray.

  • Customer: Timothy from Brunswick, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove 1 screw from the cover that hides the wiring harness, pull out the assembly and disconnect it. Swap the bottom mounting tray to the new ice maker and reverse the process. Way easier than I anticipated. No need to freeze your hands in the freezer, once you have the old one out you're working on the counter.

small plastic part in the icemaker control assembly broke, disabling entire system

  • Customer: Linda from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Ice would not dispense through front of door. There was no sound when the lever was pushed either, however, the water dispenser next to it worked fine.

  • Customer: John from Cresskill, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

Ice maker would not make ice

  • Customer: Daniel from Central, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

icemaker stopped working

  • Customer: Patricia from Urbandale, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

Broken filter cap

  • Customer: Peggy from Estes Park, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Attached new one to filter...

stopped chilling

  • Customer: Dave from Harrisville, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.

ICE maker door hinge replacement

  • Customer: Theresa from Eagle River, AK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed two hex head screws, installed new part with nut driver for two hex head screws , very easy. I broke the tab off the hinge for the ice maker door when I installed a new ice maker the week before.

Ice maker kept jamming in door flap and water overfilling

  • Customer: Tommy from Greenville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced ice maker per your installation video and started making ice right away no more problems since replacing unit

Bottom tab of ice guide broke.

  • Customer: David from Geneva, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used flat blade screwdriver to remove old guide by spreading the remaining top tabs. Inserted new guide and tipped the top forward to line up bottom tab in slot. Used screwdriver to push in tab. Once it was seated pressing in the top snapped the guide into place easily.

Replaced the drive gear on the ice dispenser

  • Customer: Jeffrey from Rockford, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video on replacing this part was spot on. The screw was a little difficult to remove at first. It had been installed ten years earlier and also had some thread lock installed. A light swat with a hammer on the end of screw driver as I was trying to remove it got the screw started without stripping the Phillips head. Once we got by that little snag, it's a piece of cake, or piece of ice if you prefer.

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.

Ice despenser stoped working, auger motor worked if door flap was opened fully manuallyw

  • Customer: Jolene from Merritt Island, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Googled the problem and after reading several posting & suggestions decided that the Ice dispenser kit would probably solve the problem. I ordered both parts on the chance that it might be only the micro switch and it was only a $10 part, the ice dispenser kit was $50. The access was really easy and the switch was installed in about 20 minutes but did not solve the problem so I proceeded with the kit. The parts came out fairly easy but our actual set up was slightly different from the video and print instructions. Our model did not have the heating ribbon on the door flap and the little barrel part was permanently attached to the refrigerator so I thought I could be in trouble. Did not realize that we had cracker the lever bracket clip during removal so my husband "brainstormed" a fix. That's what we needed the large head screw and drill for. We drilled the screw into the refrigerator so it holding the spring loaded piece tightly in position. Works fine. I was told my a repairman over the phone that the dispenser was probably not fixable on our model. I saved an expensive service call AND GOT THE DISPENSER WORKING!

Will not make ice

  • Customer: Frederick from Chesterton, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had appliance tech diagonise the problem as the ice maker module, and told me the complete ice maker was no longer available and the module alone would cost $460. Found this complete unit online ordered it and watched installation video 4 or 5 times and installed it in less than ten minutes. I had ice in 30 minutes.
All Instructions for the 10644102300
571-585 of 766