10644039602 Kenmore Refrigerator - Instructions

During our blackout the ice melted down the rod so it would not turn to release the ice to drop into your glass because of the water so we replaced the bottom portion of the ice maker which is on the inside of door under ice container and everything works great now. This happen before because of blackout and ice melted and ruin the and rusted the release

Followed the video on Parts Select and it was a breeze.

I have a side-by-side fridge/freezer, so taking out the icemaker is a bit more tricky than the video shows. I just unscrewed a nut in the back right of the mechanism (this nut is holding the icemaker in place as well as the plug cover). Once that was off it slid out pretty easy. Because the freezer is so narrow, it's a bit difficult to get it back in, but all told the repair took me about 20 minutes. Replacing this part fixed the icemaker immediately and we're so glad to have our on demand ice back! Ladies, don't be afraid of a little appliance repair!

Originally ordered parts I thought would fix ice maker. When I took apart the icemaker assembly I noticed and found the actual part that went bad. Called customer service and was able to return the parts I thought would fix the ice maker, without any problems. I ordered the correct part on the same call. Within a day or so the new part arrived and was installed within 15 minutes. Thanks to the instructions & comments posted on the "Instant Repairman" link. Awesome customer service that can not be bet.

Researched the problem on the internet. Identified the icemaker control and motor assembly as the most likely culprit. Ordered a new one. Arrived in two days. Installed it in about 15 minutes. Had ice 3 hours later.

I removed the ice maker, which consist of three 1/4 inch screws to install the water fill cup and bearing. One must loosen the front panel of ice maker to install the fill cup which consist of two standard screws, slide forward enough to install new fill cup. The removal of the Icemaker control was simple, using #2 phillips screwdriver and three screws. Unplug the control and install the new one, replace the three screws and cover. Reinstall the ice maker and within one hour cubes were dropping in the bin. I saved a lot of money repairing myself, which more than covers the shipping cost. Shipping was fast, two days.

Repaired by following the video with ease and was happy to see ice the next morning.Great service, price and advise .Thank you.

Swapped out the emitter and receiver control boards. Super easy. Watched the video on how to do it on your website.

follow instructions on web site to install motor module.Great web site. Saved me a lot of money.

the tutorial is perfectwatch Steve. The boards were bad but coincidentaly so was the motor/control unit. I satrted with the boards, got my LED codes back to normal but still could not dispense. Installed the motor/control unit and had cubes dropping in 15 minutes. Great service, great tutorials.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

I watched the quick video once to see the type, if it matched mine, and the difficulty. I went ahead and ordered the part and within minutes, I had the ice maker installed. The video was so well designed, I only had to watch it once!

A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

Just watch video from part select and following the instruction to replace the control and motor assembly.

I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!