10644039600 Kenmore Refrigerator - Instructions

The repair works perfect. My Refrigerator is work fine and dropping ice.

Just as the video described except there was a rubber fill tube hanging down from the top of the freezer that made it a little more difficult to install the new icemaker(I just had to bend it up and hope it didnt break)

I tried to put in the model ice maker sent to me but it was not an exact match to the one I was replacing. The water fill cup on the upper right side was too tall to fit over the rubber fill hose so I had to take the old ice maker apart and swap it with the new cup. Then I installed the new maker but it did not work over night. I took it back out and disassembled it and saw condensation on the electric motor housing which had turned to ice. I figured that if there was ice on the outside then there was probably some on the inside as well. I used a hair dryer to evaporate the ice/moisture and then re-installed the unit. It has worked fine ever since. I do not think that I needed the entire ice maker unit but just the timer motor. I could have saved some money and time if I had known that the motor was available by it's self. The shipping was fast for the unit but look over the unit that you are replacing and make sure the picture of the new unit is IDENTICAL to it. Watch the video PartSelect offers and it will help you a lot.

Removed refrig. door and replaced closing cam and tightened the bottom cam

I thought I would have to have a serviceman replace the unit. After watching your video, I thought I would try it. It was much easier than I had imagined. If it wasn't for your video, I probably wouldn't have tried it. Thanks for your help. I will definitely check with your company first, for the next repair odyssey.

Took ice maker main cover off. Took nut driver to remove wire cover. Unplug wiring. Slid out old unit. Put extra parts from old unit to new one required for my model. Slid new unit in.. Plugged in wiring. Installed wire covering.

I removed the on/off bail wire. I then removed the cap over the motor/control panel. I removed the 3 screws, lifted old unit out, installed new unit and then put everything back together. I had ice within 12 hours and it's run like a top since. I am a 64 y/o widow & I try to repair everything myself to save money. I'm very pleased with Part Select & will recommend them to everyone. Awesome shipping time too. Ordered on Thurs. Received on Fri. Fixed on Friday afternoon!

with video's help installation was not real difficult.

FOllowed the vedio instructions which made the installation very helpfull.

After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

Removed a total of 12 screws, unplugged the control boards, plugged-in the new control boards and replaced the 12 screws.The FAQs section of the PartSelect troubleshooting guide helped me correctly identify the control boards as the source of the problem. The LED sequence was the key to identifying the problem.

First, I went online and looked up the directions to remove the ice maker. After several attempts of removing and re-installing it, I found that one of the tines on the wheel had broken of making it impossible for the ice to dispense. I went online to PartSelect, found the exact part I needed, not the new replacement one either, and watched the proper installation directions on the website. When the part came, I did exactly what the video said, which took me maybe 10 minutes, and plugged the fridge back in - make sure you unplug the refrigerator - don't just shut it off!! I heard the water going into the maker, and about 30 minutes later I heard the first batch of ice fall into the bucket!!! It was music to my ears!!!! Oh, and by ordering from PartSelect and doing this simple repair myself, I saved $150.00!! PartSelect is now my new best friend!!!

Remove icemaker, take off Icemaker control & motor ( 3 screws ) & install new part. Started making ice in less than 24 hours. Very happy customer.

The plastic "wiper" attached to the bottom of the ice "auger" in the ice dispenser unit broke. (It was made from a plastic that was not up to the freezing temps and heavy ice loads it had to move.) The new unit seemed to be of a different type of nylon/plastic. Problem was that the small machine screw at the bottom of the auger assembly could not be removed because of corrosion. I had to drill it out. Choices then were to purchase a new auger for about 60 bucks or reassemble the unit with a new 6-32 machine screw. There will not be enough metal left to allow it to be tapped so simply clean it out well and glue in the new screw with JB Weld. Allow to cure over night and you're back in business. Ours works fine so far. Good luck!

My ice make had stopped working and I thought it was a water connection issue, however, after removing the motor cover, the plastic gear just fell to the floor. I wrote down the model number and looked the part up online. I ordered the part and it arrived a few days later. Three screws and a new motor and I had a working ice maker. Great experience.