Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644033600 > Instructions

10644033600 Kenmore Refrigerator - Instructions

All installation instructions for 10644033600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644033600
916-930 of 1,034
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker stopped making ice - repair not successful

  • Customer: David from Lewisville, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

my icemaker quit making ice

  • Customer: Eugene from Jackson, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First off, the part I ordered arrived with broken tab. I called and had no problem getting a replacement unit mailed out right away. The video repair really helped a lot. Had a little trouble with the fill tube, it was a little hard to get inside the icemaker when installing the new one. Other than that, it was a piece of cake following the video instructions.

Ice maker just quit working!

  • Customer: Keith from Sanford, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

Wouldn't make ice

  • Customer: Randy A. from Ponca City, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video, then removed old maker and installed new one. Makes ice fine now. Thanks

Ice maker stopped working

  • Customer: Stephen from Lynnwood, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching a YouTube video I was able to determine that my ice sensor was working properly. I was getting water through the door dispenser so I decided to pull the icemaker. First I removed the 2 hex head screws holding the ice door which gave me access to the icemaker. I removed the hex head screw holding the electrical plug cover on the bottom right side and removed it. I then pushed up on a plastic tab on the bottom left side of the ice maker and slid the icemaker out so I could access the electrical connection. After unplugging the electrical harness(plug/socket) I completely removed the icemaker from the freezer. The white square end cover easily pulled off the icemaker exposing the control and motor assembly. After removing the 3 screws holding the assembly on I pulled the assembly off the end of the icemaker. Installation was as simple as assembling the parts in reverse order making sure that the ice delivery male shaft "flat" mated with the "flat" on the motor drive female socket. After reassembly I went for a bike ride and when I returned about 3 hrs. later I was happy to see my icemaker was making ice again. This is actually easier than it sounds if you have any mechanical apptitude whatsoever.

Ice maker stop making ice cubes.

  • Customer: Ken from Nampa, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I saw the question listed on your website with your recommended part to repair. Instead of ordering a whole new ice maker I took the chance and ordered the recommended part for repair. I saw the video and when the part came it was really easy to replace. I only wish I had found your website earlier and not gone without ice for as long as I did. Thanks.

Would not make ice

  • Customer: David from Surprise, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both the Ice maker and the control boards as It was for a rental and I did not want to make more trips then necessary to repair. I installed the new control boards and the ice maker and the refrigerator now makes ice.

Would not make ICE

  • Customer: David from Surprise, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced both the control cards and the ICE maker and now it is working fine

Ice Door Leaking Air Into Freezer

  • Customer: Richard from Jamesport, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the lead of david from chesterfield in prying off out cover, unplugging it and setting it aside. Unscrewed and pulled out next assemply, and taped it above work area to avoid having to unplug. The pried pulled out pin to right holding ice door hinge to remove old unit. (Notice which way the spring faces before removing!) unplugged it. Ended up taking off push-dispenser handle (one screw on right) to get easier access. Then reinserted long pin being careful to have spring with two long tongs pointing down. Then put everything back together. Use all parts!

no ice cubes

  • Customer: Linda from Pawhuska, OK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your youtube repairman twice. the video was very good concerning how to do the replacement.Thank you very much this is a lifesaver for people like myself that can not afford a repair person to fix broken items at the house.

Wobble in fan made a ticking noise.

  • Customer: Andrew from Fairport, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

ice maker not making ice

  • Customer: Travis from La Crescent, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My ice maker stopped producing ice after our refridgerator was accidently turned off for 4 days. Note: the on off switch in the front does turn the unit off even though the light stays on, why we need easy access to turn off the fridge is beyond me. Regardless, I spent way more time researching the problem then doing the repair. There is 2 things that could be wrong: 1 was the infra red light located on either side of the freezer, called the transmitter/reciever. 2 was the side of the ice maker control panel. Either one or if I had to replace both it would of been less then the cost of a repair man to come to my home. Prices here a good. I started with learning the diagnostic of the ice make which is learned by watching the red light flash. That informed me that it was working ok. Reference: if you hold back the hinged plate and pretend the door is shut the light should flash, flash, pause. This means its working. I went with the other route of the control module on the ice maker. This part came fast like 2 days. I watched the video on the parts web page and it was simple to do. You do have to wait until the temp goes down below 15 degrees in order for the ice maker to kick in. I won't buy another kenmore for I have had plenty of trouble with this one and its bearly 6 years old. I'm Definetly a fan of this website. Good luck DIY ers!

ice maker quit making ice

  • Customer: Joseph from Lakewood, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked on line to see repair instruction videos on my refrigerator ice maker. When I saw how easy I went to PartSelect and order the part (control and motor assembly). I received the part in two days with the cheapest shipping option. My 33 yr old son was visiting when the delivery was made. After we opened the box, he went to the basement for tools and the rest is history. 10 minutes work and ice a couple of hours later! No problems since.

Ice maker would not eject ice.

  • Customer: Daniel from Carmel, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered a new ice maker from Partselect which arrived the next day with standard shipping. I opened PartSelects installation video on my iPad next to the refrigerator and stepped through the installation. It was as simple as removing and replacing four screws.

Filter needed replacement

  • Customer: Roy from The Villages, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.
All Instructions for the 10644033600
916-930 of 1,034