10644032600 Kenmore Refrigerator - Instructions

The refrigerator stopped working and temperatures were rising. After inspection, noticed that the compressor is not running and condenser fan not running. I ordered the inverter box and replaced the old one. Compressor started to run but condenser fan still not running. Compressor was getting hot while freezer temperature reduced to some degree. Cleaned condenser with compressed air, connected condenser fan directly to 110VAC. Refrigerator runs normally. Burning of the inverter box may be preventable. We did notice that the freezer portion of the door frame getting hot for over 3 months. This is an indication that the condenser does not provide sufficient heat dissipation. This in turn made the compressor hot and melted away some components in the inverter box which is located next to the compressor. A thorough cleaning of the condenser made the freezer door frame stay slightly warm but not hot. This condition keeps the compressor running at normal temperature. I still need the main controller which is discontinued to automatically control the condenser fan. So far the fan runs all the time and uses a bit more electricity than necessary.

We were reluctant to replace the icemaker on a 10-year old refrigerator that required a leak to be patched 2 years ago, but since the patch seems to be holding, we went ahead with the icemaker. Was about the same price as buying a portable icemaker and who wants that sitting on the counter?

Removed the broken icemaker. Removed the tray that is attached to the old icemaker and screwed it into the new icemaker. Then, I installed the new icemaker first by plugging in the control wires, then sliding the icemaker into the freezer, then screwing it into freezer. BY next morning, the icemaker made ice!

Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

Ordered part and w/ help of a friend in it went.Devlivery was prompt. Receptionist on phone was great. If every company had one like her everyone would be a happy camper.Would recommend your company to anyone.It was a most pleasant experience.

Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

The replacement was easy, especially after watching the install video. Saved over $200 by purchasing the part at PartSelect and doing the install myself. Will use PartSelect again in the future.

I did not have voltmeter to test for problem. Internet sites suggested the most common problem is the circuit boards--a sender and a receiver which detect when the ice bucket is full. I could only buy as a pair (about $94). I removed two screws of cover of receiving unit, detached the coupler, replaced the circuit board. Icemaker now works. The sender was obviously still good.

Ordered part over the phone and received it two days later.....excellent service

Had repair people in a year ago and could not find problem-They changed water flow meter valve-(costly for parts and labor) Did not solve problem!I needed ice so purchased external ice maker used for 1 year-Told myself I know it is the ice maker-Got on line and ordered from PART SELECT! Only took a few days for part to arrive-I had watched video for changing parts out on line-Took only 10 minutes to duplicate video-In 45 minutes I had first ice in over 12 months-Has been working perfect since installation!Don Smith

Took The icemaker apart saw what parts needed to be replaced ordered them online put it back together Found the person I dealt with on the phone to be very knowledgeable very happy with the company Now the ice is flowing

Followed the instructions in the PartSelect video. It was so easy. Replaced the old ice maker on Monday. Visited a friend on Tuesday. Her Kenmore Frig's ice maker was broken, would not make ice. I told her how easy it was to fix and ordered the part for her today. It should be here by Tuesday and I will install it as soon as it comes in.