Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644023603 > Instructions

10644023603 Kenmore Refrigerator - Instructions

All installation instructions for 10644023603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644023603
76-90 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Part imediately broke

  • Customer: STEVE from HUGHESVILLE, MD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 14 of 21 people found this instruction helpful
Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.

Dead condenser fan/motor

  • Customer: Drew from mountville, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 12 of 15 people found this instruction helpful
Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

Motor was noisy

  • Customer: Rick from Florence, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 12 people found this instruction helpful
I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

socket melted with bulb in it.

  • Customer: martin l. from JACKSONVILLE,, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 15 people found this instruction helpful
plastic warped in ,spaced out and, the socket snapped back in place.

Cover Pan Crisper(bottom glass shelf and frame) were broken

  • Customer: anthony from ormond beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 16 people found this instruction helpful
New part slipped right into the studs and fit perfectly

coupling on water line thru freezer door cut due to moving Refg and having to remove doors.

  • Customer: Martin from Rutherfordton, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 31 people found this instruction helpful
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.

Icemaker stopped making ice

  • Customer: James from Hampton, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 14 people found this instruction helpful
Removed 3 screws on the bottom of old ice maker in the fridge, slid out old ice maker, disconnected electrical cable,took out old ice maker. Take the plastic tray from bottom of old ice maker install on new ice maker, reconnect cable, slid in place, replace the three screws. About 3 hours later water ran in and new ice maker started to make ice. The only thing I missed was I didn't rinse out new ice maker before installation. If you don't rinse out new ice maker you have to throw away the first full bin of ice due to metallic taste.

Shelf rails were broken so the crisper tray fell out

  • Customer: Rita from Saint Charles, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
We removed the old shelf. Put the new shelf in place and slipped the crisper tray on the new rails of the replacemnet shelf. The crisper no longer falls off the broken rails when you open it. We noticed the replacemnet shelf has metal rails and the original had plastic which is probably why it broke after heavy use over 12 years.

Icemaker would not complete the cycle

  • Customer: Philip from Hope, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
First removed one screw from the bottom right bottom side of the unit. Removed the door from the front of the unit. Pushed up the locking tab on the left underside of the unit and pulled the unit partway out. Removed the plastic cover ( that was retained by the screw removed and disconnected the electrical connection) and finished removing the unit from the freezer. Removed the remaining three screws from the bottom of the unit and installed on the bottom of the new unit. I then slid the new unit partially in and connected the wiring harness and slid the rest of the way in guiding the water line into thepocket which was taller than the origional unit. Reinstalled the wire protective cover with one screw and the front cover back on the new unit. Done and is working great.

Old motor was not resetting back to proper position halting ice production.

  • Customer: Kevin from Spring, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 9 people found this instruction helpful
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

ice maker not working

  • Customer: mike from citrus heights, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

Loud noise

  • Customer: Britney from Wilmington, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 10 people found this instruction helpful
There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.

Unit would not make ice

  • Customer: william from the villages, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 13 people found this instruction helpful
After deciding it was the unit itself and not a water celenoid I ordered it from parts select. Instead of 3 to 5 business days it arived the next day after ordering. I had previously removed and reinstalled the ice maker while trouble shooting. It was easy to change it out, and works perfectly.

no ice

  • Customer: michael from gurnee, IL
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 32 of 79 people found this instruction helpful
I installed a new icemaker and ice level sensors I also had to replace crummy plastic trim parts because of poor quality and broke during disassembly

Filter and Cap were missing

  • Customer: David from Reston, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 16 people found this instruction helpful
Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.
All Instructions for the 10644023603
76-90 of 651