Models > 10644023603 > Instructions

10644023603 Kenmore Refrigerator - Instructions

All installation instructions for 10644023603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644023603
526-540 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker issue

  • Customer: Carlos from Alta Loma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Water was not filling the ice tray and the ice tray coating was comming off. After the service repairman wanted to charge me over 500.00 for just replacing the ice maker, it told him to take a hike. I bought the icemaker and the electronic controls, which controls when and how much water goes into the tray for less than 250.00 and it took me less than 15 minutes to replace.

Ice not coming out when pressing level outside freezer door.

  • Customer: Edgardo from Hackensack NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

Ice Maker stopped working after cyclying one time.

  • Customer: Jerry from Strafford MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered a new Ice Maker and replaced old one. The installation was a breeze except for the water recepticle on the right side of the Ice Maker. It was taller than the original and difficul to move the rubber water line into the new recepticle. Other than that. Problem solved. Been working great ever since.

stopped making ice

  • Customer: Marquis from Bridgeport TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the icemaker stopped making ice. The cubes would get jammed up and finally just stopped all together. Removal of the icemaker and installation of the new one was pretty easy. The only problem was getting the electrical plug undone from the old unit. We have a lot of calcium in our water and I guess it finally ate through and ice was forming under the unit. It was five years old so not bad really. All is good....quick delivery. Thanks.

The refrigerator would not defrost and would freeze up and no longer cool.

  • Customer: Mike from Frankfort IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

Loud fan motor

  • Customer: Brian from Saint Augustine FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

ice maker no longer worked

  • Customer: John from Bulverde TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The unit came out easily but the wire harness connector just didn't want to disconnect. The ice cold plastic was very difficult to work with and I had to use a screw-driver edge to pry it up and apart.

Ice Maker had stopped making ice

  • Customer: Connie from Mt. Vernon KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.

glass broken

  • Customer: Kenrick from Lake Arrowhead CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

Not making ice

  • Customer: George from Orange Park FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch replacement video then went from there. It was a simple replacement. Icemaker working and wife is happy:)

Unit not making ice

  • Customer: Donald from Casselberry FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove ice unit to take out ice. Remove both boards and replace.Had to unplug refig to thaw out water line because it froze when unit would not make ice.

Icemaker quit

  • Customer: JL from Colby KS
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video, it was just a matter of pulling one screw, changing the icemaker and reinstalling the screw. Super simple and now we have ice!

ice maker was leaking and cubes getting stuck

  • Customer: bill from escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as the video described except there was a rubber fill tube hanging down from the top of the freezer that made it a little more difficult to install the new icemaker(I just had to bend it up and hope it didnt break)

ice maker quit working

  • Customer: Rudy from Tyrone GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to put in the model ice maker sent to me but it was not an exact match to the one I was replacing. The water fill cup on the upper right side was too tall to fit over the rubber fill hose so I had to take the old ice maker apart and swap it with the new cup. Then I installed the new maker but it did not work over night. I took it back out and disassembled it and saw condensation on the electric motor housing which had turned to ice. I figured that if there was ice on the outside then there was probably some on the inside as well. I used a hair dryer to evaporate the ice/moisture and then re-installed the unit. It has worked fine ever since. I do not think that I needed the entire ice maker unit but just the timer motor. I could have saved some money and time if I had known that the motor was available by it's self. The shipping was fast for the unit but look over the unit that you are replacing and make sure the picture of the new unit is IDENTICAL to it. Watch the video PartSelect offers and it will help you a lot.

The heat element went out.

  • Customer: Michael from Peachtree GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought I would have to have a serviceman replace the unit. After watching your video, I thought I would try it. It was much easier than I had imagined. If it wasn't for your video, I probably wouldn't have tried it. Thanks for your help. I will definitely check with your company first, for the next repair odyssey.
All Instructions for the 10644023603
526-540 of 651