10644022602 Kenmore Refrigerator - Instructions

Used the instructions provided on the web site. They were very clear and easy to follow. I might add, I am an 82 year old 30 year military retiree and I am used to problem solving. Yours in service, Jimbo

took screwdriver, took out old parts. replaced with new parts. plugged fridge back in, turned on receiver. We have ice! Real Easy to install! Thank you Part Select.

The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

A repairman wanted $600.00 to fix our ice maker. I paid him $88.00 for his "service call" & asked him to leave. I ordered & replaced the ice maker machine & the ice maker still would not work, so I replaced the 2 optics boards next. Replacing the ice maker was most challenging because the plug is so hard to get at, but the 2 optics boards were pretty easy. Just watch the video on PartSelect.com. Work slowly & take your time when pulling out & replacing the optics boards. There were a total of 6 screws for the 2 optics boards. It took me approximately 10 minutes to replace both boards, & now my ice maker is working perfectly! I am thrilled!!

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

Watched the video it was right on, no problem.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Watch the movie adjacent to the part on the ordering list,follow said instructions you can't miss.Thanks for the movie,the ease ordering the friendly associate that took my order and your timely shipment.Once again thanks for everything.Thomas J

Repair was easy. But what I really liked was the prompt/timeliness of the correct part delivery. That's what really made the difference. (My ice bucket is FULL of ice).THANKS!!

Watched video

Used 1/4 inch nut driver with swivel to remove the part retaining screw. Held new part into place and installed the retaining screw. Challenge was not hitting the level and putting water on me and the floor during installation. Relatively easy installation as long as you have patients.

Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

1. I first confirmed that the problem was a bad Infrared Ice making control board (Watched flashing of red light on right side of freezer - solid light would not occur when holding flap on left side of freezer). 2. I unplugged refridg,3. unscrewed both sides of the control unit and disconnected wire clips to the electronic boards. 4.popped in new Boards on both sides and connected clips onto each board. 5. Screwed the boards and covers to walls of freezer. 6. Plugged power back into wall and checked Red light again (when holding flap in, a continuous red light verified it would work). closed freezer and shortly ice was being made. Simple process. (careful using Screwdriver to help take wire off of boards - a small clip holds wire clip on - you need to stick screwdriver into back of clip while unconnecting). Easy and my ice worked perfectly.