Models > 10641569800 > Instructions

10641569800 Kenmore Refrigerator - Instructions

All installation instructions for 10641569800 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641569800
406-420 of 422
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator and freezer was not cooling. Lights inside refriogerator working . Compressor and fan was not on.

  • Customer: Cary from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug the refrigerator. With nut-driver and/or screw driver remove the lower back cardboard panel to access Start device. Use needle nose pliers to remove bracket holding Start Device along with capacitor. Disconnect the wiring connector from Start Device. Carefully, pry Start Device from compressor. Remove capacitor from Start Device. Replace the capacitor to the Start Device. Connect the Start Device with the capacitor to the compressor being mindful of the three male pins. Plug the electrical connector back into the Start Device. Finally, reconnect the bracket. . Reinstall the lower back cardboard panel. Plug in the appliance. Very simple and easy to install. Note: If the compressor and fan do not come on, reset the defrost switch which is located inside the refrigerator side underneath the right side of the refrigerator temperature selector with the flat head screw driver.

Heard Ticking every minute - Fridge/Freezer not Cold

  • Customer: Chris from Bellingham WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the start relay in about 5 minutes and plugged the fridge in and it started working. Easy repair to get fridge working again.

Cracked Crisper Drawer

  • Customer: Richard from Huntsville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the damaged unit and inserted the replacement.

Lower Door Closing Cams Worn down

  • Customer: Raul from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

fridge turned itself off, melting often

  • Customer: Irene from Margate FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I vacuumed the back and underneath, hoping it will solve the problem, but after about 2 weeks of hoping I succumbed.... finding the proper wrench was the most time consuming. After removing the screws, the face plate removal was the most challenging. You have to pry the top part carefully away (we used a knife), after it just drops down. Used a flat screw driver to loosen the wire harness, after that the rest was less than child's play. We are still in the testing mode, but so far so good. Freezer freezes, ice maker drops the ice cubes (not melting), fridge is humming. Wish us good luck.

Bottom door shelf broken

  • Customer: Jim from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened package, opened fridge door snapped new shelf into place, no problem, took less than 1-2 minutes tops.

Refrigerator door was not closing "automatically", over time the plastic cams had worn out.

  • Customer: Mike from Egg Harbor Township NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

On the back of shelf the snap catches broke .

  • Customer: Scott from Oconomowoc WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed broken shelf and snapped in new one

refrigerator and freezer would stay frozen.

  • Customer: Jack from Poplarville MS
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Broken Door Bin

  • Customer: Evelyn from Redwood City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy and amazed at how fast my order was processed. I received the parts next day. Wow!

broken crisper drawer

  • Customer: marie from metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The part fit perfectly. All I had to do was slide it in. Very speedy delivery and I am very satisfied with the service and would recommend your wedsite to anyone. Marie

Door would not close properly

  • Customer: George from Loudon TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions on line suggested I buy a lower door closing cam and a thimble top which I did. When I went to install I noticed that the door hinge with cam was also warn down. I had to again place an order and again remove the door to install. I would suggest those having this problem that they look at the hinge with cam also before ordering.

The refrigerator door would not close completely

  • Customer: Terri from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the refrigerator door (after taking everything out of the shelves). Took the old Lower Door Closing Cam off (it was totally worn down), installed the new one, rehung the door. Rehanging the door took a couple of tries to get it properly aligned. Very easy fix, We thought we had to replace the refrigerator since it is 14 years old, but this fixed the problem completely!

door made clacking , thunking noise when opened

  • Customer: BILL from ADVANCE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

Plastic on both the shelf and drawer either cracked or broken

  • Customer: Robert from Lumberton TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Open door on refrigerator, wide. Clean shelf off. With right hand grasp shelf and lift and slide shelf toward you until shelf is free of refrigerator. Slide new shelf back into refrigerator. Replace items back on shelf. For drawer open refrigerator door, wide. Open drawer by pulling forward and lifting at the same time. Take new drawer and replace by sliding new drawer back into refrigerator. Tools are used just to make you look cool.
All Instructions for the 10641569800
406-420 of 422