Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10641562801 > Instructions

10641562801 Kenmore Refrigerator - Instructions

All installation instructions for 10641562801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641562801
61-75 of 442
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken drawer

  • Customer: Thomas from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
replaced

My drawer had been broken and I needed a new one.

  • Customer: Jennifer from Birmingham, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)

Broken Crisper Frame And Pan

  • Customer: Mauricio from National City, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
Jus took me seconds to replace both items. No problem.

compressor didnt turn on

  • Customer: gerardo from el monte, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 21 people found this instruction helpful
changed the starter connected to the compressor

Door closer cam broken

  • Customer: Monty from Tigard, OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
Removed door from refrigerator. Had to use pliers to pull out the broken piece in the bottom of the door. Appears to have gotten "glued" in when they blew in the insulation - was very sticky. All went well after than.

However, it seams that while there are two holes to select from when mounting the lower cam, neither one really works. When closed the cams still don't line up and the door sites just a bit higher than it should and the upper cam's riser is sitting about 1/2 way on the lower cam's. It seems this part is not designed to exactly replace the original or there is something I'm missing.

Door would not auto close

  • Customer: James from Hampton, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100.
Thanks

Refrigerator door fails to close on its own like it is designed to.

  • Customer: Jay from Oconomowoc, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 6 of 6 people found this instruction helpful
The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.

The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.

part broken

  • Customer: wilfredo from athens, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
i replace the old broken one, very simple and easy,thanks very much for the part, the price was really good better than sears, they were charging me for the same pretty much $100.oo, so thanks for everything, the time frame delivery was excelent!!!!! so i'll be keep you name first on my providers list for my next job......!!!!!!!
sincerely;
wilfredo Uztariz

Freezer/refrigerator no air flow

  • Customer: Jim from Au Sable Forks, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 9 people found this instruction helpful
Using a 1/4" nut driver and a philips screwdriver I removed all the screws in the shelf brackets and coil cover and removed coil cover. Removed fan blade and then faulty motor (held in with clips) Installed new motor-two wires (power) and ground (green) pushed fan blade back on and tested, then reinstalled all panels and shelf brackets.

The refrigerator door was hanging low and not closing properly. Hence the refrigerator was not maintaining the temperature

  • Customer: jairaj from North grafton, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

Motor intermittently not working.. Warm Frig.

  • Customer: Joseph from Gurnee, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Very easy. Take panel off and replace motor.. All wires matched fine. Easiest applance repair I've done..

Refrig Door Cams wore out and made noises when opening and closing.

  • Customer: Michael from Lewisville, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 6 of 7 people found this instruction helpful
Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.

Crisper drawer tilted to the right when pulled out

  • Customer: William from Heathsville, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.

Both parts were broken and required replacement.

  • Customer: Patricia from Inglewood, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 14 people found this instruction helpful
The broken part was removed and new part installed without any trouble.

door was making a poping sound upon opening and closing

  • Customer: Tony from Mesquite, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 5 of 6 people found this instruction helpful
First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.
All Instructions for the 10641562801
61-75 of 442