Models > 10641514100 > Instructions

10641514100 Kenmore Refrigerator - Instructions

All installation instructions for 10641514100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641514100
526-540 of 578
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator door would not close completely

  • Customer: Terri from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the refrigerator door (after taking everything out of the shelves). Took the old Lower Door Closing Cam off (it was totally worn down), installed the new one, rehung the door. Rehanging the door took a couple of tries to get it properly aligned. Very easy fix, We thought we had to replace the refrigerator since it is 14 years old, but this fixed the problem completely!

door made clacking , thunking noise when opened

  • Customer: BILL from ADVANCE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

Refrigerator would stop running but when touched it would run again

  • Customer: Wilton from Huntley IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

broken bin

  • Customer: Lawrence from Burlington VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just lifted out one out and sit new one in place

Water was running into refrig from freezer and ice cream was soft

  • Customer: William from Delano MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH

Refrigerator freezing regardless of settings.

  • Customer: James from Taylorsville NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

Broken slides on crisper drawer

  • Customer: Mary from Pickens SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply washed the part and installed

FAN WASRUNNING BUT COMPRESSOR WOULD NOT KICK IN

  • Customer: Kenneth from Spring Grove IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
uSEDNUT DRIVER TR REMOVE REARDUST COVER AND THAN A SCREW DRIVER TO SNAP OFF COVER PROTECRING STARTER COMMPONENTS..RE[PLACED STARTER AND RELAY. REPLACED COVERS..DONE..iT WAS A SNAP..mY ONLY COMPLAINT WAS THE INSTRUCTIONS REALLY DID NOT EXPLAIN FULLY WHICH PART IN MY PACKAGE WAS FOR MY UNIT...I FIGUERED I OUT BY PROCESSOF ELIMATION,,,

Broken Crisper pan

  • Customer: Amanda from Windermere FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the broken one out and put the new one in. I am a very skilled craftsman. ;-)

no ice maker at all

  • Customer: David from Apopka FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Crisper pan no longer held in place due to breakage of the lip.

  • Customer: Ken from Spokane WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out the old one an put the new one in. I was impressed with how easy it was to work with partselect.com, I had alway ordered through Sears before, but from now on I will be using partselct.com for ordering parts. Got the part in two days with free shipping and $20 les than Sears that did not have the part in stock.

Cracked Crisper Pan

  • Customer: Heather from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
SUPER EASY!!!! I pulled the old one out and put the new one in. Perfect fit and it took less than 60 seconds. This web site was about $30 cheaper than ordering from Kenmore and it was identical. I ordered my Crisper Pan on Wednesday and got it Friday. Highly recommended!!!!!!!!!

See below

  • Customer: Patricia from Hobe Sound FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defective. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you

Refrigerator stop cooling

  • Customer: Ba from Van Nuys CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Door would not close properly and was out of vertical alignment

  • Customer: Timothy from Ashburn VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.
All Instructions for the 10641514100
526-540 of 578