Models > 10641269801 > Instructions

10641269801 Kenmore Refrigerator - Instructions

All Instructions for the 10641269801
436 - 450 of 559
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was constantly running and not getting hot
Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.
Parts Used:
Refrigerator Crisper Drawer With Handle
  • HENRY from WARMSPRINGS, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Broken slides on crisper drawer
Simply washed the part and installed
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Mary from Pickens, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Crisper pan
Took the broken one out and put the new one in. I am a very skilled craftsman. ;-)
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Amanda from Windermere, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no ice maker at all
We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.
Parts Used:
ICEMAKER
  • David from Apopka, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
refrigerator not working
read instructions from your site my wife repair refrigerator before i got home
Parts Used:
Run Capacitor Start Device
  • HERBERT from CHARLOTTE, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Crisper pan no longer held in place due to breakage of the lip.
Pulled out the old one an put the new one in. I was impressed with how easy it was to work with partselect.com, I had alway ordered through Sears before, but from now on I will be using partselct.com for ordering parts. Got the part in two days with free shipping and $20 les than Sears that did not have the part in stock.
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Ken from Spokane, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Cracked Crisper Pan
SUPER EASY!!!! I pulled the old one out and put the new one in. Perfect fit and it took less than 60 seconds. This web site was about $30 cheaper than ordering from Kenmore and it was identical. I ordered my Crisper Pan on Wednesday and got it Friday. Highly recommended!!!!!!!!!
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • Heather from Oklahoma City, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door would not close properly and was out of vertical alignment
Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.
Parts Used:
Lower Door Closing Cam
  • Timothy from Ashburn, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
When I placed the glass cover in a sink of lukewarm water, it shattered
All I did was removed the stickers and place it in the frame - no tools required. It fit perfectly and is since it is clear (the original one has a grid pattern in it) I can easily see everything in the drawer below. I will be more careful in cleaning this one - apparently the temperature difference from cool to warm caused it to break, so I will just wipe this one down rather than submerging it in water.
Parts Used:
Refrigerator Shelf Glass
  • Mary from Sacramento, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Parts Used:
Refrigerator Door Switch
  • Joseph T. from Morgantown, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Need to replace a broken icemaker
Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.
Parts Used:
ICEMAKER
  • Jill from MARIETTA, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Our 6 year old refrigerator stopped keeping food cold
It was pretty simple. I watched a few videos on youtube. Diagnosed the problem. Ordered the part from PartSelect. It arrived a few days later. Followed the online directions for replacing the thermostat. Voila!!! We have a working refrigerator again!!! I'll NEVER call a repair man again. Thank you PartSelect!!!
Parts Used:
Thermostat
  • Kenneth from Muldrow, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drawer broken
old drawer out - new drawer in how easy can it get????
Parts Used:
Refrigerator Crisper Drawer with Humidity Control
  • sue from boyertown, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
clicking noise two places when opening and closingdoor
removed door and replaced the two parts
Parts Used:
Lower Door Closing Cam Door Cam - Black
  • Donald from Bradenton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Door Not Closing
All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.
Parts Used:
Lower Door Closing Cam Door Cam - Black
  • Ricardo from Buda, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10641269801
436 - 450 of 559