Models > 10641262800 > Instructions

10641262800 Kenmore Refrigerator - Instructions

All installation instructions for 10641262800 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641262800
61-75 of 440
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator door was hanging low and not closing properly. Hence the refrigerator was not maintaining the temperature

  • Customer: jairaj from North grafton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

Freezer/refrigerator no air flow

  • Customer: Jim from Au Sable Forks NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Using a 1/4" nut driver and a philips screwdriver I removed all the screws in the shelf brackets and coil cover and removed coil cover. Removed fan blade and then faulty motor (held in with clips) Installed new motor-two wires (power) and ground (green) pushed fan blade back on and tested, then reinstalled all panels and shelf brackets.

My drawer had been broken and I needed a new one.

  • Customer: Jennifer from Birmingham AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)

refrigerator door wouldn't remain closed

  • Customer: Thomas from Fairfax VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 9 people found this instruction helpful
The plastic lower door closing cam was worn down. Replacing it was very simple: remove the top door hinge by unscrewing three nuts; lift the door off the lower hinge; unscrew and remove the lower door hinge; screw the new plastic lower door closing cam on to the new door hinge; screw the new lower door hinge; lift the door back on to the lower door hinge; screw the top door hinge.

It was not coming out of defrost cycle

  • Customer: Dale from Flemingsburg KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 24 people found this instruction helpful
First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

compressor didnt turn on

  • Customer: gerardo from el monte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
changed the starter connected to the compressor

Plastic portion of shelf broke along the back edge

  • Customer: Suzanne M from West Hills CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Remove the old shelf and slid the new shelf in - couldn't have been easier!

part broken

  • Customer: wilfredo from athens GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
i replace the old broken one, very simple and easy,thanks very much for the part, the price was really good better than sears, they were charging me for the same pretty much $100.oo, so thanks for everything, the time frame delivery was excelent!!!!! so i'll be keep you name first on my providers list for my next job......!!!!!!!
sincerely;
wilfredo Uztariz

broker cover to crisper

  • Customer: dean from los angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
the piece fit perfectly and delivery was within a couple days. very satisfied.

burned out Evaporator Fan Motor

  • Customer: Robert from Surprise AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

bottom and middle door bin broke

  • Customer: Fred from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
it snapped right in easy .

The icemaker in the fridge stopped working

  • Customer: Rebecca from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 11 people found this instruction helpful
The repair was so simple. I removed the old icemaker in about 3 minutes and unpacked and installed the new one is about 10 minutes. It was literally a matter of removing a few screws! Eady to follow instructions!

light inside fridge was flickering and clicking

  • Customer: bill from escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 8 people found this instruction helpful
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

fridge ouit cooling

  • Customer: danny from adelanto CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 11 people found this instruction helpful
where the wires crossed at the start relay, 20 years of vibration allowed them to short out and burn out the start relay ..since i have 2 identical fridges i switched the run capacitor to determine it was'nt bad too...ordered a start relay wednesday nite and got it friday morning...cold fridge by noon...good service and the part was exactly the same as the original....
All Instructions for the 10641262800
61-75 of 440