Maytag Range Igniters

Your Price

$57.35

Maytag Range Bake Igniter

★★★★★

37 Reviews

PartSelect Number PS11747217

Manufacturer Part Number WP9758079

This part ignites the gas to light the oven burner.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

Greg from North Baltimore, OH

Bake/broil would not work

Replaced igniter and also DSI/direct spark igniter did not fix problem. Called out repairman turned out to be bad gas valve. Replaced that part , now stove works fine. Read more...

Your Price

$69.04

Maytag Range Igniter-OVEN

★★★★★

53 Reviews

PartSelect Number PS11770066

Manufacturer Part Number W10918546

This flat style gas oven igniter has ceramic housing and comes with a connector.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Little to no heat when baking
See more...

Installation Instructions

sharnette from baltimore, MD

our oven would not heat up

My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have . Read more...

Videos!

Your Price

$57.79

Maytag Range Flat Style Oven Igniter Kit

★★★★★

55 Reviews

PartSelect Number PS1573892

Manufacturer Part Number 12400035

The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both bake and broil elements, and it can replace both short and long igniters. However, it cannot replace round style oven igniters. If your igniter glows for 90 seconds or more without igniting the burner, this means it is too weak to open the valve. The element in your igniter may have shorted it and it might not glow at all, or it might only glow orange or red. It needs to glow white hot; if it cannot get hot enough the gas will not be released from the safety valve and it will be impossible to light the burner in your oven. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, a variety of plug ends, and an instruction sheet. The body length is 3 3/4 inches, and the element inside is approximately 1 1/2 inches. This replacement part has an amperage range of 3.3 to 3.6. The element inside this igniter is extremely fragile, do not touch it. Before you start repairing your oven or range, make sure you have unplugged it and shut off the gas supply.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

James from Ferndale, MI

Oven would not work but the Broiler did

The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside. Read more...

Your Price

$93.48

Maytag Range Oven Igniter - Vertical Mount Bake and Broil

★★★★★

46 Reviews

PartSelect Number PS2085070

Manufacturer Part Number 74007498

This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven element is giving off no heat or very little, or is not heating evenly. You may also notice a smell of gas. The ignitor may still be glowing, but could still have gone bad. You will need a 1/4-inch nut-driver and a 5/16 nut-driver. Open the oven door and pull the door off the hinges to completely remove. Pull out the racks. Using your 1/4-inch nut driver, take out the screws at the bottom rear end of the oven, which will allow you to completely remove the bottom. Unscrew the nuts holding the igniter in place. Remove the igniter with the 5/16 nut driver. You should now have access to remove the old igniter.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

James from Berwick, ME

Oven wouldn’t heat up properly

My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.

Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.

I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.

Keep track of your screws and put it back together the way you found it except for the igniter that is.

Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.

Good luck. Read more...

Videos!

Your Price

$41.20

Maytag Range Top Burner Igniter

★★★★★

20 Reviews

PartSelect Number PS2082000

Manufacturer Part Number 74004053

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

roy from East Providence, RI

gas burner ignitor failure

Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order. Read more...

Your Price

$58.40

Maytag Range Flat Style Oven Igniter

★★★★★

12 Reviews

PartSelect Number PS387058

Manufacturer Part Number 786324

The flat style oven igniter is also known as a range oven igniter. The function of this part is to glow extremely hot in order to ignite the gas for the oven burner. With this flat style oven igniter, you must reuse the original bracket from your original igniter. Be very careful during installation to not touch the black element part of the flat style oven igniter as it is very fragile. If your oven does not heat you should check to see if your igniter is glowing. If your igniter is glowing and the oven is not heating there is a chance that the igniter is not strong enough to heat your oven and it will need to be replaced.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Little to no heat when baking
See more...

Installation Instructions

John from Niles, MI

Oven wouldn't heat. Glow ignitor was weak and wouldn't ignite flame.

After shutting off the gas and removing the oven door, which simply slid off of the hinges, I removed the oven plate. The ignitor was attached to the manifold. I removed that and noted the wires were attached back behind a hole in the back of the oven. I thought I would have to access them from the back but when I pulled on them I was able to reach them from the front. I was surprised to find plastic lugs covering the wire ends, rather than ceramic. I attached the new ignitor wires and reused the plastic lugs, as no ceramic ones came with the new ignitor. I carefully slid the new ignitor back into the cage/shield attached to the manifold and replaced the manifold. I then turned the gas back on and tested the ignitor (which worked perfectly) before replacing the oven plate. The repair took less than 30 minutes, but my wife and I thoroughly cleaned the door and interior while we had it apart. The hardest part was getting the door back on the hinges, but this too was accomplished after several attempts. The oven heats up beautifully now. Read more...

Your Price

$25.35

Maytag Range Surface Burner Spark Igniter

★★★★★

8 Reviews

PartSelect Number PS11746068

Manufacturer Part Number WP8523793

This part helps your burner ignite and produce flame.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Daniel from Needham, MA

spark igniter was weak and not lighting the flame.

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together. Read more...

Your Price

$87.08

Maytag Range Oven Bake Igniter

★★★★★

7 Reviews

PartSelect Number PS11752876

Manufacturer Part Number WPW10324262

Fixes these symptoms

Gas igniter glows, but will not light
Little to no heat when baking
Will Not Start
See more...

Installation Instructions

Mark from HOLLAND, MI

Faulty ignitor

Remove bottom plate take screws and hex head nuts remove wire unscrew ingnitor reverse process with new ignitor very easy Read more...

Your Price

$47.20

Maytag Range Spark Ignition Electrode

★★★★★

6 Reviews

PartSelect Number PS11757464

Manufacturer Part Number WPY0316773

This spark ignition electrode lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in length. It pulls current from the ignition circuit; the more current it pulls, the warmer it gets. When the spark ignition electrode reaches a certain temperature, it creates a spark. This electrode comes with the mounting bracket you will need to successfully install the part. Before installing your new part, shut off the gas supply and unplug your appliance. This part cannot be repaired. If it is damaged or faulty, it must be replaced.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

HUY from ALISO VIEJO, CA

Broken Electrode, no spark

Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner Read more...