Make sure you haven't got the discount earlier.
Roper Washer Dryer Combo Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Roper Washer Dryer Combo Parts
- Burning smell
- Leaking
- Noisy
- See more...
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
- Burning smell
- Spinning Issues
- Spins slowly
- See more...
- Leaking
- Shaking and Moving
- Spinning Issues
- See more...
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
compoments and reassembled.
Test run machine. Ran like new! Read more...
- Not Heating
- See more...
- Marks left on clothes
- Noisy
- See more...
- Noisy
- See more...
- Door Pops Open
- Door won’t close
- See more...
- Will not agitate
- Will not drain
- Will Not Start
- See more...
I read the do-it-yourself explanation posted by Paul From Glendale CA and followed his instructions.
1. Unplugged the Washer and disconnected the hoses, so I could slide the washer into the kitchen.
2- Unfastened the two screws in the front lower corners of the controls panel and tilted is back. Unfastened the old lid-switch wiring from the control panel.
3. Remove the clips at the two corners under the control panel. I rotated the cover forward to clear it from the back and lifted it off and set it off to the side.
4. While I had the Washer disassembled I vacuumed out all the accumulation of dust, etc.
5. Removed the lid switch and unfastened the ground wire.
6. Installed the new switch and reassembled the Washer.
7. I did not read Paul's reassembly instructions closely enough. The front flange of the cover goes UNDER the steel frame on the washer. I spent 30 minutes trying to get the cover on, then finally figured that out on my own. Once I got the flange under the frame, it took about five minutes to get the cover on, the clips in and the control panel back into positions and reassembled.
The entire process is not particularly difficult. Had I read the "UNDER the frame" part earlier, the entire repair would have taken no more than 45 minutes.
Having another person to help reinstall the cover would be helpful. The cover is not heavy but it is a little awkward to handle and having another person to help line up the back cover, etc. will make the reassembly even easier. Read more...
- Will not agitate
- See more...
Roper Washer Dryer Combo Appliance Types
Related Roper Washer Dryer Combo Parts
Popular Roper Washer Dryer Combo Models
Below are the most popular Roper Washer Dryer Combo models we have. Enter your model number in the search box to find your model.