Make sure you haven't got the discount earlier.
Parts That Fix General Electric Dishwasher GDT535PSM0SS Leaking
Leaking is a commonly reported symptom for the GDT535PSM0SS General Electric Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GDT535PSM0SS General Electric Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This part is a replacement gasket for your dishwasher. The gasket creates a seal at the bottom of the dishwasher tub, so water does not leak out while the dishwasher is running. If you notice water leaking out onto the floor, you should inspect the gasket for damages and replace as necessary. The gasket is gray in color and is approximately 22 inches long. It is made of plastic and is sold individually. This is a genuine OEM part sourced directly from the manufacturer.
Customer Repair Stories
lower door gasket deteriorated/moldy
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach t ... Read more hem. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.
-
Stephen from MATTAPOISETT, MA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Wrench set
Gasket at the bottom of the door disintegrated.
-
D from LE CENTER, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the floor after you run your dishwasher, it may be an indication that the gasket is loose or damaged. If your door gasket is damaged, it will need to be replaced. To replace the gasket, simply pull the old gasket out of the groove it rests in, and press the new gasket into place. This part is made of black rubber and is sold individually.
Customer Repair Stories
tub gasket was damaged
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.I ... Read more t did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
-
Susan from STATEN ISLAND, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Bad tub gasket
-
Larry from HAMBURG, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This diverter valve assembly is sourced from the original manufacturer for use in dishwashers. The assembly controls the flow of water between different parts of the appliance. It directs water to either the upper or lower spray arms during different stages of the wash cycle, ensuring efficient cleaning of dishes throughout the dishwasher. The valve may become damaged or worn down over time due to frequent use and exposure to heat and chemicals. If the assembly is faulty, you will likely notice leaking from under the door and less water reaching the spray arms. It is best to replace the assembly promptly to avoid further damage to the dishwasher.
Customer Repair Stories
Diverter assembly leaking
-
Lisa from PULASKI, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Strange noise coming from the dishwasher, later a small leak appearing underneath
-
Donaldo from ALTADENA, CA
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the appliance is not in use, you may need to replace the inlet valve. It measures approximately 3 inches by 4 inches and is made of metal and white plastic.
Customer Repair Stories
Dishwasher would not start Would run if you added 2 qt. water manually
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to ... Read more easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.
-
Mark from FAIRFAX, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
No water
-
Jeffrey from BENNINGTON, VT
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your General Electric Dishwasher DOOR VENT SEAL
Customer Repair Stories
I had a hole in the drain line of my dishwasher.
-
Tina from SOUTH WEST CY, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers