Microwave Oven Combo Circuit Boards and Touch Pads

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Shop By Brand

Popular Microwave Oven Combo Circuit Boards and Touch Pads

Your Price
$241.01
  In Stock
Microwave Oven Combo Display Control Board
★★★★★
★★★★★
1 Review
PartSelect Number PS1022528
Manufacturer Part Number WB27X10858
Fixes these symptoms
Your Price
$375.78
  In Stock
Microwave Oven Combo Digitron
★★★★★
★★★★★
1 Review
PartSelect Number PS1018741
Manufacturer Part Number WB27X10856
Installation Instructions
William from EAGLE, ID
Flashing display
Replace Advantium 120 flashing display.

Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.

For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet

On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)

Work the display panel off and support it until the connectors are removed.

There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.

Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.

Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.

Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.

Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
Your Price
$293.72
  In Stock
Microwave Oven Combo Microwave Inverter
★★★★★
★★★★★
1 Review
PartSelect Number PS2342258
Manufacturer Part Number W10217711
The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.
Fixes these symptoms
Your Price
$390.02
  In Stock
Microwave Oven Combo Electronic Clock Oven Control
★★★★★
★★★★★
1 Review
PartSelect Number PS773585
Manufacturer Part Number WB27T10411
Please note: With this control the wiring could be differ from the original. It will possibly need to be installed by an appliance repair person.
Your Price
$158.70
  In Stock
Microwave Oven Combo POWER BOARD
★★★★★
★★★★★
1 Review
PartSelect Number PS1020967
Manufacturer Part Number WB27X10861
Your Price
$64.66
  In Stock
Microwave Oven Combo Wall Oven Noise Filter Board
PartSelect Number PS8747022
Manufacturer Part Number 5304492543
Videos!
Your Price
$513.56
  In Stock
Microwave Oven Combo Electronic Clock Control Board
★★★★★
★★★★★
1 Review
PartSelect Number PS11743900
Manufacturer Part Number WP71003424
This electronic clock assembly is seven and a half inches long. It is three inches wide and is intended for use with a range's control panel.
Fixes these symptoms
Installation Instructions
Cheryl from Mesa, AZ
No clock display
1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!) Read more...
Your Price
$80.91
  In Stock
Microwave Oven Combo Noise Suppressor
PartSelect Number PS11742574
Manufacturer Part Number WP4451985
This part controls the voltage and helps to reduce interference on the control board
Your Price
$19.08
  In Stock
Microwave Oven Combo Noise Filter Board
PartSelect Number PS3500969
Manufacturer Part Number W10422269
The purpose of this board is to smooth out the voltage in the microwave into a more usable level.
  No Longer Available
Microwave Oven Combo Oven Control with Harness
★★★★★
★★★★★
2 Reviews
PartSelect Number PS953773
Manufacturer Part Number WB27T10566
Installation Instructions
WILLIAM from FRANKLIN, OH
Oven Panel lights too dim to read and probe stopped working
1. Turn off breaker
2. Remove grill that around built in microwave; remove two top screws and to bottom (open oven door).
3. Remove two screws on the control panel.
4. Swing out and allow panel to suspend from its wire holder.
5. Trace the two harness cables from the old control board and disconnect from the counterparts inside the unit.
6. Remove the "ribbon" connector (do not damage, be gentle)
7. Remove the four screws holding the old control in place.
8. Place the new control board in place (do not connect the ribbon connector yet).
9. Plug in the harness to their respective receiving locations in the unit.
10. Install the "ribbon" connector into the new control panel.
11. Reverse steps 4-1 above ensuring all connections are solid and made correctly.
12. Turn on the circuit breaker and enjoy a "like new" oven! Read more...

Microwave Oven Combo Circuit Board or Touch Pad Brands

Back to Top