White-Westinghouse Refrigerator Parts

Westinghouse Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular White-Westinghouse Refrigerator Parts

Your Price
$29.13
  In Stock
Door Shelf Retainer Bar
★★★★★
★★★★★
(120)
PartSelect Number PS734935
Manufacturer Part Number 240534901
This door shelf retaining bar, also known as refrigerator door bar retainer or fridge door rack, is a genuine part sourced from the original manufacturer. It is a white This manufacturer-certified Door Shelf Retainer Bar, sometimes otherwise known as the door rack or bar retainer, is a white, plastic part which can be easily installed onto the inside of the refrigerator or freezer door to hold items on the door shelves. It holds items in your fridge and will show physical damage if broken or warped, at which time it should be replaced. Check your user manual and model number to see if this part is right for you. No tools are required for this installation, the part should simply snap into place. This part measures roughly 25 inches wide, 3 inches high, and 5 inches deep. This part is sold individually, and we recommend checking the other door shelf retaining bars on your refrigerator or freezer at the same time as ordering this part to ensure that no others need to be replaced, as they often wear or warp at similar speeds.
Fixes these symptoms
Installation Instructions
Cynthia from Long Beach, CA
The retainer door shelf broke 3 years ago
I just snapped the new shelves in place and !voila! I should've done this years ago. Read more...
Your Price
$40.23
  In Stock
Door Shelf Retainer Bar
★★★★★
★★★★★
(52)
PartSelect Number PS734936
Manufacturer Part Number 240534701
The Door Shelf Retainer Bar, also known as a refrigerator door rack, is a white, plastic part which can be easily installed onto your fridge door. It holds items in your fridge and will show physical damage if broken, at which time it should be replaced. Check your user manual and model number to see if this part is right for you. To install this part, you will need to remove the old one by unlocking the tabs, which can be slid with your fingers. To install the new shelf, line it up with the shelf cut-outs, over the tabs, and gently press it down to lock it into place. This part generally fits the middle door shelf of refrigerators. This is a part that frequently requires multiple parts per refrigerator. Because it is sold individually, you will need to purchase as many door racks as necessary to complete your repair.
Fixes these symptoms
Installation Instructions
Lannie from Buffalo, WY
door rack was broken
pulled broke rack off, snapped new one in place. Yeah!! No more broken jars on the floor. Read more...
Your Price
$5.97
  In Stock
Crisper Cover Support - Front
★★★★★
★★★★★
(63)
PartSelect Number PS2358880
Manufacturer Part Number 241993101
This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is an easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
Fixes these symptoms
Installation Instructions
Peter from Amherst, NY
Support studs were broken
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. Read more...
Your Price
$29.46
  In Stock
Refrigerator Door Bin
★★★★★
★★★★★
(179)
PartSelect Number PS429724
Manufacturer Part Number 240323001
This door bin (Bottom Door Bin, Refrigerator Door Bin, Door Shelf Bin, Refrigerator Door Bin) is a movable bin mounted on the inner door to hold food items, bottles, and jars. Over time, a cold refrigerator can cause plastic to become fragile and break down. This can lead to other issues in the refrigerator. When the door bin will not hold securely onto the inner door panel, it must be replaced. This door bin measures 5.75 inches high, 16 inches wide, by 4.25 inches deep and is made of white plastic. Sold individually.
Fixes these symptoms
  • Clicking sound
  • Door won’t open or close
  • Ice maker not making ice
  • See more...
Installation Instructions
Erik from Evans, GA
Aged parts broken
After sitting in a cold refrigerator for year after year, plastic becomes brittle and breaks. This is what started happening to my shelves and door bins. The problem a lot of times is getting the right part since some of the parts do not have numbers.

This website gives a accurate description and best of all photos on an inch grid, so I can measure what I have and find what I need. This time everything was perfect and fit easily. took no time and just like that I have almost double the space again. Funny how that works. Once before I didn't get the right piece so just pay attention to the dimensions.
Read more...
Your Price
$38.30
  In Stock
Drawer Support Rail - Right Side
★★★★★
★★★★★
(104)
PartSelect Number PS430917
Manufacturer Part Number 240530701
This manufacturer-certified drawer support rail supports the right side of the sliding drawer. It is a track that helps the drawer slide open and closed with ease. If you are having trouble opening or closing your fresh food drawer, check the support rails for any blockage, or visible damage. If the rail is damaged, it should be replaced to ensure no further damage is done to the drawer itself. The repair is straightforward: unscrew and remove the existing support rail, then fasten the new rail in place. This genuine OEM replacement part is made of plastic and is white in color. NOTE: This part is sold separately from the left side drawer support rail. The part measures approximately 16 inches long by 1 inch high.
Fixes these symptoms
Installation Instructions
Jane from Owosso, MI
broken refrigerator door shelves
snapped right on and removed screws, insert and replace screws. Read more...
Your Price
$132.95
  In Stock
Refrigerator Ice Maker Assembly
★★★★★
★★★★★
(60)
PartSelect Number PS12364147
Manufacturer Part Number 241798231
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
Fixes these symptoms
  • Clicking sound
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Juan from Miami, FL
Broken ice maker
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. Read more...
Your Price
$8.89
  In Stock
Crisper Support - Rear
★★★★★
★★★★★
(15)
PartSelect Number PS2358879
Manufacturer Part Number 241993001
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your user manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
Fixes these symptoms
Installation Instructions
Peter from Amherst, NY
Support studs were broken
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. Read more...
Your Price
$25.99
  In Stock
Defrost Timer - 60Hz 120V
★★★★★
★★★★★
(34)
PartSelect Number PS423801
Manufacturer Part Number 215846602
This Defrost Timer works like a clock by switching on the defrost heater circuit after a predetermined amount of compressor run time. This allows the defrost circuit to clear the evaporator of ice or frost to maintain proper airflow. The defrost timer is located in the control housing which is in the refrigerator section of your appliance. If this part is not working, it can lead to temperature increases in your refrigerator. If the compressor circuit fails, no cooling will take place; if the defrost circuit isn't activated, ice will quickly build up on the evaporator coils and reduce airflow and efficiency. If the timer doesn't advance or if the contacts have no continuity, the timer will need to be replaced. This timer measures approximately 3 inches long and 2.5 inches wide, and is constructed of plastic and metal. It comes in black/white/silver and is sold individually. This replacement part features 1 defrost timer.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
Stephen from Warrington, PA
Fridge got warm and freezer coils were frosted
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

Once back cover was removed thermostat was located attached to top pipe going into coil using a spring clamp.

Cut the wires just outside the crimp connectors going into thermostat. Released the spring clamp buy squeezing botton together.

Removed old badly corroded thermostat.

I wish I had attached the crimp connectors to the new thermostat wires before mounting it. Reaching way in the back, while turning shoulders verticly and trying to get the wire connectors set from both sides was awkward and uncomfortable...The biggest PIA of the whole task.

Once connected I let the fridge (thermostat) cool for 10 min. Turned the dial defrost timer to get it into defrost mode. Stupidly touched the heating element to see if it was getting warm...it was very hot.

Coils steamed...every looked like it was working. Unplugged, put back cover back on and retattached drawer mounts.

Plugged back in and everying is working great!
Read more...
Your Price
$72.56
  In Stock
Refrigerator Water Inlet Valve
★★★★★
★★★★★
(81)
PartSelect Number PS7784018
Manufacturer Part Number 242252702
The function of the Refrigerator Water Inlet Valve (Triple Solenoid Water-Valve, Water Valve, Water Inlet Valve, Refrigerator Water Inlet Valve Assembly) is to release water from the supply line when activated, and send it through to your water dispenser or ice maker in your refrigerator. The water inlet valve is located at the back of the refrigerator, and connects to the water supply. The valve can break from material fatigue or normal use. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. This valve measures approximately 7 inches long and 4.5 inches wide, and is constructed of plastic and metal. It comes in blue, and includes the valve and mounting bracket.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Jose from Alexandria, VA
water leaking out of refrigerator
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps. Read more...
Your Price
$68.96
  In Stock
Door Gasket - White
★★★★★
★★★★★
(45)
PartSelect Number PS2331952
Manufacturer Part Number 241872513
This fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air outside.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Fridge and Freezer are too warm
  • See more...
Installation Instructions
Matthew from Washington, DC
Refrigerator door gasket torn
No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is the basic process:
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...
Read more...

Appliance Type

Related Parts

Popular Westinghouse Refrigerator Models

Below are the most popular Westinghouse Refrigerator models we have. Enter your model number in the search box to find your model.