Whirlpool Microwave Circuit Boards and Touch Pads

Your Price

$85.97

Whirlpool Microwave Acu Pcba Service Assy For W10849829

★★★★★

2 Reviews

PartSelect Number PS16620391

Manufacturer Part Number W11552018

This control board is an authentic replacement part sourced directly from the manufacturer to ensure compatibility with your microwave. It has dimensions of 4 inches by 8.25 inches. The control board is responsible for controlling the various functions and features of the microwave such as the power levels and cooking times. If it is faulty, your microwave will likely be unresponsive when you try to input commands, it may be unable to start or complete heating cycles, or it may display error codes. Additionally, a burning smell coming from inside the microwave may be a sign of a faulty control board.

Installation Instructions

jerry from BRYAN, TX

The microwave magnet would start when the door closed w/o a keypad signal.

Unplugged the microvave, removed the phillips screw holding the right hand section of the microwave in place (Note: This screw is found by looking through a vent opening in the TOP of the microwave body.). Lifted up and out on the right hand section of the microwave. At this point the right hand section is completely unattached to the microwave body. Unplugged all of the polarized wiring harnesses and removed the screw holding the green wire to the board holder. Removed the screws holding the board to the right hand section and installed the new board. Reversed the procedure to put the microwave back together. Note: Look at and manipulate the keypad ribbon recepticle on the new board to see how to remove and reattach the ribbon, if needed. Read more...

Your Price

$231.71

Whirlpool Microwave Inverter

★★★★★

1 Review

PartSelect Number PS2342258

Manufacturer Part Number W10217711

The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.

Fixes these symptoms

No heat
See more...

Your Price

$101.55

Whirlpool Microwave Cntrl-elec

PartSelect Number PS16620240

Manufacturer Part Number W11545876

Your Price

$436.63

Whirlpool Microwave Cntrl-elec

PartSelect Number PS12348595

Manufacturer Part Number W11179310

Your Price

$124.76

Whirlpool Microwave Led Display Board

★★★★★

4 Reviews

PartSelect Number PS11748663

Manufacturer Part Number WPW10124269

Installation Instructions

Krystal from YORK, PA

The LED display on the microwave was no longer functional. Some lights still showed, but not enough to be able to tell the time or validate timer settings.

1) Identified the breaker that the microwave was connected to and turned it off.
2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws. Read more...