Washer Transmissions and Clutches

Shop By Brand

Popular Washer Transmissions and Clutches

Your Price
$49.66
  In Stock
Clutch Assembly
★★★★★
★★★★★
(55)
PartSelect Number PS334641
Manufacturer Part Number 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining is worn out, the clutch assembly will not rotate properly to release the brake. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate there is an issue with your clutch. If the washer spins when the washer basket is empty but not when it’s full, or if the assembly begins to turn blue, you may need to replace the clutch assembly. This assembly includes a brake cam driver, blue springs for large capacity washers, a black spring for compact washers, and the installation instructions. It’s constructed of plastic and metal, and comes in beige/silver.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
Andrew from SLC, UT
spin cycle did not engage
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly Read more...
Your Price
$38.42
  On Order
Washer Drive Pulley
★★★★★
★★★★★
(15)
PartSelect Number PS10057144
Manufacturer Part Number W10721967
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.
Fixes these symptoms
  • Noisy
  • Pumps but will not spin
  • Spins slowly
  • See more...
Installation Instructions
Jerry from WALLA WALLA, WA
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done. Read more...
Your Price
$33.56
  On Order
Drive Hub Kit
★★★★★
★★★★★
(14)
PartSelect Number PS6012095
Manufacturer Part Number W10528947
This drive hub kit (part number W10528947VP) is for washers. Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to your parts diagram for a complete list of parts included. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Noisy
  • Pumps but will not spin
  • Shakes and moves
  • See more...
Installation Instructions
Allison from RICHFORD, NY
Hub had warn its grooved teeth off and washer wouldnt agitate
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed. Read more...
Your Price
$29.89
  In Stock
Basket Hub Kit
★★★★★
★★★★★
(21)
PartSelect Number PS11723155
Manufacturer Part Number W10820039
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
Fixes these symptoms
Installation Instructions
Kevin from CLARK, MO
The washer was making a horrible noise during the spin cycle
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitrating oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great Read more...
Your Price
$54.18
  In Stock
Shift Actuator - 120V 60Hz
★★★★★
★★★★★
(12)
PartSelect Number PS11747977
Manufacturer Part Number WPW10006355
This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
Fixes these symptoms
  • Pumps but will not spin
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
David from Los Alamos, NM
Lid Lock light blinking, machine will not start
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure Read more...
Your Price
$58.49
  In Stock
Shift Actuator - 6 Pin
★★★★★
★★★★★
(3)
PartSelect Number PS11769864
Manufacturer Part Number W10913953
Fixes these symptoms
  • Pumps but will not spin
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
Beverly from MADISON, IN
Wouldn't spin properly
Replaced the gears that were eaten up, the retainer and the actuated. All parts but the spring are plastic. Did all according to your instructions. Happy to report all went well. Washer is working again. Read more...
Your Price
$242.01
  In Stock
Gearcase
★★★★★
★★★★★
(6)
PartSelect Number PS341974
Manufacturer Part Number 3360629
This is used in your direct drive washer that has a neutral drain.
Fixes these symptoms
  • Noisy
  • Pumps but will not spin
  • Will not agitate
  • See more...
Installation Instructions
Troy from Storm Lake, IA
Tub wouldn't turn, but motor would allow it to drain.
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tipped the washer on its back. I had to remove two clips to take the water pump off of the motor, then removed the two screws and clips which held in the motor. After removing the motor, I found the coupler was bad. To remove the gearcase, I took out the softener dispenser and removed one bolt to take out the agitator. Under the agitator was a clip. Three bolts held the gearcase to the frame. After removing them, the gearcase pulled straight out the bottom. Replacement was just a reverse process, with the addition of a light coat of grease to the gearcase shaft. Read more...
Your Price
$12.54
  On Order
Speed Governor
PartSelect Number PS11753017
Manufacturer Part Number WPW10330804
Also known as a clutch.
Installation Instructions
Michael from MONTROSE, CO
Mixer only had 2 speeds with the smell of electrical burning.
This mixer was given to me 8-10 yrs ago with only 2 speeds (cant believe i waited this long to fix it). Repair went good, wasn't sure what i should replace so i replaced Control board, control plate, governor, grease in the gears and the transmission gasket. I first took any and ALL measurements for any screws on the control plate, this will help when you set your mixer speeds when its all back together. When installing the new governor i used a 10mm socket and a mallet to seat it all the way till it stops on the set pin. installed the new control board, with thermal grease on the back of the plate(very important). Didn't need to replace the grease in the gears, but i figured since i was in there id replace it. (No smells and all gears work) I used it to ground 5lbs of elk into burger (speed 4) after repairs and it worked great. Still have about 15lbs left to do and itll do it with out braking a sweat. Maybe i should open up a repair shop to fix these suckers...lol its that easy. What really helped with the repairs is the youtube video from Partselect. Second to none with a step by step on how to replace and repair just about anything on your mixer. Good deal, if i need to replace anything else i know where to go! Thanks Read more...
Your Price
$124.91
  In Stock
Washer Drive Shaft And Shifter Assembly
★★★★★
★★★★★
(7)
PartSelect Number PS7788161
Manufacturer Part Number AEN73131403
HOUSING ASSEMBLY,CLUTCH This drive shaft and shifter assembly (part number AEN73131403) is for washers. Drive shaft and shifter assembly AEN73131403 connects the motor with the washplate, and shifts the drive system between agitate and spin. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Your Price
$182.75
  In Stock
Shaft & Drive Tube Assembly
★★★★★
★★★★★
(3)
PartSelect Number PS3652839
Manufacturer Part Number WH38X10019
Fixes these symptoms
Installation Instructions
Dana from MIDDLEPORT, NY
Bearing was making noise on spin cycle
Disassembled washer removed shaft and drive tube assembly reinstalled new unit and replaced split nut during assembly. Read more...

Brands