EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Back
Keep typing for more specific results...
Keep typing for more specific results...

Simplicity Lawn Mower Seals and Gaskets

Popular Simplicity Lawn Mower Seals and Gaskets

Your Price
$9.69
  In Stock
Simplicity Lawn Mower Engine Oil Seal
★★★★★
★★★★★
2 Reviews
PartSelect Number PS9151828
Manufacturer Part Number 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaft, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.
Installation Instructions
rodney from MUSCATINE, IA
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet to remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions Read more...
Your Price
$9.69
  In Stock
Simplicity Lawn Mower Gasket-crkcse/015
PartSelect Number PS9076878
Manufacturer Part Number 697110
Genuine OEM replacement part used on a variety of Engines. This item is made with Composite Material and it is sold individually. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. The gasket measures .015 Thick.
Your Price
$6.40
  In Stock
Simplicity Lawn Mower Gasket-float Bowl
PartSelect Number PS9064482
Manufacturer Part Number 693981
This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance. When replacing this Gasket you would need a Screwdriver and a set of Wrenches.
Your Price
$8.09
  In Stock
Simplicity Lawn Mower Engine Oil Seal
★★★★★
★★★★★
1 Review
PartSelect Number PS9277860
Manufacturer Part Number 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. Refer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
Your Price
$8.58
  In Stock
Simplicity Lawn Mower Gasket, Foam
PartSelect Number PS8881765
Manufacturer Part Number 1707335SM
It is an OEM item which is made for use with Murray, Snapper, and Simplicity lawn mowers. This gasket provides a tight seal for the arbor housing. Over time the material will wear out and it may get compressed eventually requiring a replacement to ensure the unit functions properly. Refer to the specific diagrams of your model for the exact location and the correct installation of the new part. It is a high-quality gasket which is made of a durable foam material and is sold as an individual component. You will need a wrench set to take apart the housing and gain access when replacing this gasket.
Your Price
$6.42
  In Stock
Simplicity Lawn Mower Gasket-rocker Cover
PartSelect Number PS9307288
Manufacturer Part Number 806039S
This is an original part from Briggs & Stratton. The rocket cover gasket is compatible with many small engines. The cardboard composite gasket is designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.
Your Price
$6.40
  In Stock
Simplicity Lawn Mower Gasket-float Bowl
★★★★★
★★★★★
1 Review
PartSelect Number PS8945656
Manufacturer Part Number 281165S
This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.
Installation Instructions
FRANK from EASTANOLLEE, GA
Screw can out of the carburator throttle baffel and stuck in the exhaust valve
No compression. Removed the cylinder head. freed the screw, checked the valve to see if it still sealed. Turned the head over with the valves in it, install a spark plug, fill the head dome with gas and see if any leeks out over a 2 hr period. If not you are good to go. Reinstalled every thing with new gaskets and a new carburetor screw. Set the valves to spec. Complete the rebuild and there you have it. Rebuild the carburetor while you have it apart. This motor runs great !!! Read more...
Your Price
$53.18
  In Stock
Simplicity Lawn Mower Crankcase Gasket With Bolts
PartSelect Number PS11829358
Manufacturer Part Number 594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. It is made out of composite material and it is sold individually. To complete this repair you will need a wrench. Includes one (1) gasket and ten (10) bolts. This will need to be tightened with torque to 300 inch pounds.
Installation Instructions
rodney from MUSCATINE, IA
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet to remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions Read more...
Your Price
$6.40
  In Stock
Simplicity Lawn Mower Gasket-intake
PartSelect Number PS9063862
Manufacturer Part Number 692555
This is an authentic replacement part manufactured for use with Briggs and Stratton small engines. The special intake gasket seals the connection between the breather tube and carburetor. It is recommended to replace the gasket when servicing the carburetor, or air cleaner to assure a good seal when reinstalling the parts. The intake gasket is sold individually.
Your Price
$6.40
  On Order
Simplicity Lawn Mower Seal-o Ring
★★★★★
★★★★★
1 Review
PartSelect Number PS9294749
Manufacturer Part Number 691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine running improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.
Installation Instructions
FRANK from EASTANOLLEE, GA
Screw can out of the carburator throttle baffel and stuck in the exhaust valve
No compression. Removed the cylinder head. freed the screw, checked the valve to see if it still sealed. Turned the head over with the valves in it, install a spark plug, fill the head dome with gas and see if any leeks out over a 2 hr period. If not you are good to go. Reinstalled every thing with new gaskets and a new carburetor screw. Set the valves to spec. Complete the rebuild and there you have it. Rebuild the carburetor while you have it apart. This motor runs great !!! Read more...

Related Simplicity Lawn Mower Parts