Shindaiwa Cultivator Parts

Shindaiwa Cultivator Primer Pump The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

Shindaiwa Cultivator Fuel Filter This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine sounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

Shindaiwa Cultivator Washer 5 This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener becomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

Shindaiwa Cultivator Gasket This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. This gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

Shindaiwa Cultivator Recoil Starter Assembly

★★★★★

★★★★★

2 Reviews

The Recoil Starter Assembly, aka the Recoil Assembly, is a kit that includes the pulley, a return spring, the starter cord, and the pawls which engage the flywheel to turn over the engine. The components of this assembly are constructed of steel and plastic. The kit can be installed with a screwdriver and is rated as "Easy" to install (Tip: line all the parts up to install). This kit starts the engine, and you will know it is broken if the pull cord will not retract, or the engine is not engaging after it is pulled. The rope may also break. When the part breaks due to fatigue or general wear, it must be replaced. The part attaches on top of the engine where the flywheel is located.

Shindaiwa Cultivator Washer 5

Shindaiwa Cultivator Air Purge Body Assembly

Shindaiwa Cultivator Insulator

Shindaiwa Cultivator Pre-Filter, Foam This Foam Air Filter is a yellow, foam part, used to filter out contaminents from entering the engine. It lays on top of the main air filter, is rated as "Easy" to install, and requires a screw driver . If your filter is dirty and discolored then it has worn out, and the part should be replaced. Refer to your make, model and diagram to ensure this air filter is correct for your machine.

Shindaiwa Cultivator Filter, Air This Air Filter is used to stop debris and particles from entering the carburetor and engine which would cause damage. If this part is worn or damaged, the engine may become hard to start and run rich or there may be a loss of power. This means the part is broken and should be replaced. It should also be replaced according to the manufacturer's schedule. This filter is constructed of white foam and attaches inside the air cleaner housing. Installation is rated as "Easy" and requires a screw driver, and socket set. Refer to your make, model and diagram to ensure this is the correct part for your machine.