Roper Dryer Seals and Gaskets

Roper Appliance Parts

Popular Roper Dryer Seals and Gaskets

Your Price
$64.69
  In Stock
Roper Dryer Rear Drum Felt Seal
★★★★★
★★★★★
41 Reviews
PartSelect Number PS8691753
Manufacturer Part Number W10612022
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
Fixes these symptoms
Installation Instructions
Paul from Monmouth, IL
intermittant heat
First I shut off the gas supply and disconnected the dryer vent and unpluged the unit so you can access the rear of the dryer. Then I removed the rear cover. This is where you will find your thermostats and fuses. Holding the new part next to the one to be replaced I transfer the wires one at a time so as not to get them mixed up, then unscrew the old part and install the new one. Insert a flat blade screwdriver under the top cover in the 2 front corners to unsnap it from it's clips, also at this time you need to remove the 2 screws that hold the upper part of the lint filter tube to the lid, then lift the lid to expose the drum ( I tilted the dryer back as far as the flex gas line would allow me to and rested the top lid against the wall without removing it, to many wires). Behind the front cover in the top right corner is the plug for the door switch,un-plug it and also there are 2 screws one in each corner. After that lift the front cover straight up and pull it away from the cabinet ( it has clips at the bottom to hold it in place). Reaching under the drum on the right side pull down on the belt tensioner and release the belt from the motor then you can remove the drum. Laying the drum down on it's front edge I removed the rear felt seal and took a piece of sand paper to rough up th old glue and clean off some of the felt that was still stuck to the drum. Following the directions from the seal package I put the glue around the edge of the drum and re-installed the new felt. This is a good time to clean out your dryer, while the glue sets up. A shop vac works the best, but be carefull not to suck up the money, it will help pay for the repair ( I found over a dollar in change ). At this time I also changed the coils on the gas valve, remove the 2 screws that hold the clamp and replace them one at a time. Re-install the drum with the belt on it, fold it and push it through the tensioner and put it on the motor pulley. rotate the drum to make sure that the felt is not kinked under itself, re-install the front cover bottom clips first, then the 2 screws and the plug for the door switch, pull down the lid and snap it in place, before installing the rear cover this is a good time to remove the rear cover to the lint chute and clean in there also ( it's easy to see why there are so many dryer fires). Re- install that cover and the rear cover and vent tube, turn your gas back on and check it for leaks ( even if you didn't disconnect it) plug your dryer back in and get busy catching up on the laundry that you haven't had a chance to do because your dryer broke, then smile and think about all the money you saved by doing this simple repair your self. Thanks Parts Select Read more...
Your Price
$9.76
  In Stock
Roper Dryer Lint Trap Housing Seal
★★★★★
★★★★★
8 Reviews
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot. Read more...
Your Price
$66.91
  In Stock
Roper Dryer Door Gasket
★★★★★
★★★★★
17 Reviews
PartSelect Number PS11731610
Manufacturer Part Number W10861521
This door seal does not include the adhesive glue.
Fixes these symptoms
Installation Instructions
Manolak from MURFREESBORO, TN
Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine.... Read more...
Your Price
$40.08
  In Stock
Roper Dryer Rear Drum Seal with Adhesive
★★★★★
★★★★★
2 Reviews
PartSelect Number PS333333
Manufacturer Part Number 239087
Includes high temperature adhesive.
Fixes these symptoms
Installation Instructions
Lauren from Mckinney, TX
The dryer was leaving rust marks on our clothes.
After my husband disassembled the cabinet and removed the drum, we used a putty knife to remove the old seal and carefully glued the new one in place. (A 2 man job to do it without leaking glue everywhere.) We then replaced the belt, following the picture sent by PartSelect and put everything back. (We put all small pieces in labeled envelopes so that putting it back together was easy.) Another helpful hint - take a few digital pictures beforehand in the event that you need to see it to put it back together! Read more...
Your Price
$74.19
  In Stock
Roper Dryer SEAL-DOOR
★★★★★
★★★★★
8 Reviews
PartSelect Number PS11766744
Manufacturer Part Number W10906683
Fixes these symptoms
Installation Instructions
alice from wickliffe, OH
seal came of dryer door
romoved from pkg. and fit it to the door. no tools needed. best of all the part came in 24 hrs and was fixed with out delay of waiting from a store that was out of our area. great costumer service!!!!! Read more...
Your Price
$69.34
  In Stock
Roper Dryer Seal and Bearing
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11773177
Manufacturer Part Number W11035878
This front panel seal kit doesn't include the plastic retainers, reuse the old retainers. No glue is needed, the seal stretches to fit.
Fixes these symptoms
Installation Instructions
Stephen from Springfield, MA
Dryer making loud squealing noise when running
The (front) bearing and seal are not metal parts but a fabric and and mesh like material. It is somewhat like a fabric belt made to hold up a pair of trousers. The belt sits in a channel that goes around the door on the inside of the front panel. To get to the combination bearing/seal you remove two screws that are located under the cover of the lint trap. These have to be removed to lift the top. Then using a putty knife or screw driver you must pop the top (which snaps down on plastic clips) at the front corners. The top lifts up and folds back on hinges. The front is attached to the sides by one screw on each side near the top. A nut driver will remove then easily. Once the 2 screws are removed lift the front panel about 2 inches to disengage the front panel from the clips that hold the front attached to the sides near the bottom. When you remove the front panel the dryer drum will literally fall out so you want to get hold of it before pulling the front panel away so it isn't damaged and and doesn't damage the gas burner assembly which is under the drum to the left side. The drum is very light. I supported it with an empty shoe box while the front was off.
Once the front is off you'll see the bearing/seal on the inside of the front panel and it will be obvious how to remove the old one and place the new one. There are three pegs on the front panel that receive the three holes in the fabric bearing/seal. The seal will stay in place while you remove the shoe box and put the front cover back on. The drum fits over the seal like a lid on a jar and just slides on the fabric when the drum rotates. Low tech but the drums slides easily on the bearing material and seems to last a long time.

I also did the rear dryer seal. This is similar to the front. To do this you follow the procedure above but to get to the real seal you will have to remove the drum. It will fall out on its own if the front panel is removed. The drive belt goes around the drum. It is about 3/8th of and wide and just wraps around the drum without any teeth or channels or anything. Let the belt fall to the bottom as you lift the drum forward and out of the cabinet. The drum is light. Just put it on the floor and strip off the old rear seal which is glued on. It too is fabric. Clean up the drum a little and fit the new seal on the drum. Once the seal is on the drum you can lift the edge of the fabric seal and glue the fabric flange to the drum. This becomes pretty obvious once you have the seal on the drum. If you put the glue on the drum first you will make a mess. Put the seal on properly and the lift the edge to apply the adhesive all the way around. The adhesive sets enough in a hour or so. Put the drum back in and replace the front panel. Don't forget the drive belt. It goes around the drive motor that is located on the bottom of the dryer on the right, around or over an idler pulley (my older model does not have a idler wheel but rather a bracket with a "slide" that the belt runs over that keeps sufficient tension on the belt to drive the drum. If your belt falls off the motor and the idler pulley falls out it may be confusing how the belt goes in. My idler bracket is held in slots on the bottom of the cabinet merely by the tension of the belt - no screws or anything. I suggest that you put the belt around the drum first, then the drive motor. You will have slack in the belt and it becomes a little more obvious how the idler pulley (which is mounted on spring steel) goes in and takes up that slack and keeps modest tension on the belt. The rubber side of the belt goes against the drum, the leathery side is the outside.
Read more...
Your Price
$71.92
  In Stock
Roper Dryer Rear Drum Seal Kit
★★★★★
★★★★★
10 Reviews
PartSelect Number PS334194
Manufacturer Part Number 279408
This seal kit for large capacity gas and electric clothes dryers includes a seal, an adhesive, and an instructions sheet. This felt seal for the back of the drum is sewn with red thread.
Fixes these symptoms
Installation Instructions
CHRISTOPHER from MOUNT AIRY, MD
Squeaky dryer
My wife had been complaing about excessive noise from our 25 year old dryer so after DISCONNECTING the dryer from the wall outlet I popped the top panel loose @ the front with a screw driver @ each front corner @ took a look. No cause was visible so I removed the rear cover & still nothing so I laid the dryer on it's back to remove the front cover. First the 2 wires to the door switch were disconnected then the 2 screws @ the top corners that hold the front panel to the side panels were removed. The front panel then slid up & lifted off exposing the front of the drum, belt & support pulleys. Upon inspection I found the bottom support pulley sleeve bearing to have worn out. Both pulleys were replaced because they only come as a pair now along with the tensioner pulley (idler pulley), the belt & the rear lip seal on the drum since it had a 4" section missing from the edge @ one point (all of these were the original components). Replacing the rear drum seal took the most time because the old adhesive had to be removed. I did this first so the glue could set while I installed the new pulleys & belt. By the time they were installed, the glue had set enough & I could continue the re-assembly.
We now have a 25 year old dryer that sounds like it's new & @ a fraction of the cost
Read more...
Your Price
$55.60
  In Stock
Roper Dryer Bearing and Seal Kit
★★★★★
★★★★★
2 Reviews
PartSelect Number PS334171
Manufacturer Part Number 279264
This front bearing and seal kit comes with the adhesive.
Fixes these symptoms
Installation Instructions
Leslie from Townsend, GA
Drum was binding because of worn bearing supporting front of dryer drum
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to glue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!! Read more...
Your Price
$58.95
  In Stock
Roper Dryer Rear Felt Drum Seal with Adhesive
★★★★★
★★★★★
2 Reviews
PartSelect Number PS334265
Manufacturer Part Number 279735
Creates a seal between the rear panel and the rear of the drum.
Fixes these symptoms
Your Price
$76.69
  In Stock
Roper Dryer Door Gasket
★★★★★
★★★★★
4 Reviews
PartSelect Number PS11741447
Manufacturer Part Number WP3390733
This gray door gasket is used to seal the dryer door when closed. It does not come with the adhesive.
Installation Instructions
Timothy from Sterling, MA
burner wouldn't light
removed the back of the appliance disconnected the vent pipe. Found the problem was a flying squirrel had committed suicide in the vent pipe and as a result had blown the thermal fuse. Tested the fuse to see it was blown with a multi-meter. Ordered the fuse from PartSelect online. fair price shipping was quick. Received the new fuse in 4 days and had the dryer working again in about 10 minutes. Read more...

Related Roper Dryer Parts