Roper Cooktop Parts

Roper Appliance Parts
Shop By Appliance Type

Popular Roper Cooktop Parts

Your Price 4.04
  In Stock
Drip Bowl - 6 Inch
★★★★★
★★★★★
(54)
PartSelect Number PS11750108
Manufacturer Part Number WPW10196406
This drip bowl is used for electric cooktops and ranges, it is designed to sit under a six-inch surface burner. It catches the drips and spills coming from the cookware on the surface burner. This drip bowl is chrome, and it has a diameter of 8 inches. You need to remove the burner element to replace this part. Line the hole up with the element terminal blocks, and ensure the new bowl is flush with the surface of the cooktop before replacing the burner element. Drip bowls need to be replaced when they are lost, damaged, or you are no longer able to clean them adequately. This replacement part is sold individually.
Fixes these symptoms
Installation Instructions
Joe from Greeley, CO
oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then removed element and replaced with new
.
Read more...
Your Price 36.19
  In Stock
Heating Element
★★★★★
★★★★★
(37)
PartSelect Number PS11742505
Manufacturer Part Number WP4391960
If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom, regardless of the brand of dryer. To gain access to the drum glide, you will have to open the cabinet on the dryer. This drum glide is sold individually but it is important to note that they should be replaced in pairs. Before beginning this repair, it is important to disconnect the dryer from the power source. The tools required for this repair are a putty knife and a 5/16 nut driver.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • See more...
Installation Instructions
Bill from Morristown, TN
Dryer quit heating. Suspected heating element was open
Unplugged the 220 volt source. Disconnected the vent line from the back of the drier. Removed the six screws holding the back panel with a 1/4 inch nut driver. Tipped the drier up at a 45 degree angle against the wall to give better access to the inside. Removed the screws holding the two thermostats to the side of the heater box and laid them aside. Disconnected the two red power lines to the heater element. Removed the large screw at the top of the heater box and removed the flexible bracket holding the heater box, then lifted the heater box up and away from the drier. Removed the one screw holding the heater element inside the heater box and pulled out the old heating element. The old element was open as found using an ohmeter on the two main terminals. Threw away the old element. Removed the new heating element from the box and slid it into the heater box making sure to align the terminal bracket with the hole in the heater box for the reinstallation of the mounting screw. Tightened this screw. Remounted the heater box to the two mounting slots and reinstalled the flexible mounting bracket to the top of the heater box and installed and tightened the large screw holding this bracket. Cut off and removed the old electrical push-on terminals from the two red power wires for the heater element. These were discolored and oxidated from the conducted heat over the years of operation. Using the supplied short red leads with push-on terminals already installed, I wire tied these new leads to the existing red power leads and pushed them onto the heater element terminals. Rechecked the soundness of the twisted wire connections to make sure they were tight. Replaced the back panel and reinstalled the six 1/4" screws with the 1/4' nut driever. Reinstalled the driver vent line and tightened its holding ring. Slid the drier back into position on the floor. Checked the level and readjusted the leveling legs for a steady floor stance. Reinstalled the 220 volt power connecter and set the controlls for a drying cycle. Let the drier run for aproximately 1 minute and then checked the air temperature inside the drier. IT WAS NOW PRODUCING HOT AIR. Project completed successfully and I was now a HERO in my wifes eyes. Absolutely no technical problems encountered. Just remember, unplug the drier before starting ANY repairs. To forget this COULD RUIN YOUR DAY. Read more...
Your Price 11.44
  In Stock
Drip Bowl - 8 Inch
★★★★★
★★★★★
(13)
PartSelect Number PS2366563
Manufacturer Part Number W10196405RW
This part is located beneath the element and catches any spills.
Fixes these symptoms
Installation Instructions
Michael from Kings Park, NY
Drip bowls were rusty and rotting through
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better! Read more...
Your Price 11.60
  In Stock
Surface Burner Plug-In Block Kit
★★★★★
★★★★★
(14)
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms
Installation Instructions
Jon from Oakley, CA
Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new.
I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.

Way to go Part Select.com

Jon
Read more...
Your Price 4.30
  In Stock
Hex Nut
PartSelect Number PS11738304
Manufacturer Part Number WP112432
This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts and screws in order to hold items firmly together. This piece is a fastener that attaches one item to another. This part has several advantages, the main one being that it is universal and can be used with most pieces and appliances in your home. This hex nut is an original equipment manufacturer part, meaning it is directly sourced from the manufacturer.
Installation Instructions
Heather from Pittsburgh, PA
Incoming power hot lead broke loose from mounting block and short-circuited
First I turned off power at the service panel. Then, I pulled out the range and tried to remove the access panel. The screw which held the black lead from the incoming power to the range wiring terminal had broken loose from the mounting block. It had welded itself to the panel, so I had to pry it loose. I tried to reattach it to the mounting block, but the block was cracked.

I turned on power at the service panel and used my digital multimeter to test the AC voltage of the receptacle to make sure it fell within the correct limits.

When the new mounting block and power cord arrived, I removed the screw that held the broken mounting block to the back of the range. Then, I used a screwdriver to remove the leads that attached the old power cord to the broken mounting block and range wiring terminals. The screw and nuts which held the old black lead and range wiring terminal to the block were welded together. This was the most difficult part of the repair. I was able to back them off a little bit, but not enough to remove the range wiring terminal. While holding one end of the screw in the pliers, my Dad used the heavy duty cut off wheel on my Dremel tool to cut the screw in half and free the terminal.

Then, we reversed the process to attach the new wiring block to the back of the range, incoming power cord to wiring terminals and range wiring. We plugged it back in and had it working before my dinner party.
Read more...
Your Price 68.66
  In Stock
Broil Element
PartSelect Number PS340509
Manufacturer Part Number 326795
This is a five-loop broil element for an oven, range, or stove. It is approximately 11-3/4 inches wide and 18-5/8 inches long with approximately 11-3/4 inches between terminal connections. It features a.25-inch male terminal push-in connection for easy replacement and a hanger style mount. It is 3000/2500 watts and 240/208 volts. This broil element is located on the inner upper wall of your oven. Be sure your element wires do not fall through the wall of your oven when you uninstall the existing part. The wires are short and will make your repair more difficult because they are difficult to retrieve.
Installation Instructions
John from Houston, TX
The bake element was arcing/smoking and needed immediate replacement.
I removed (2) mounting screws from the back of the oven and pulled the element out far enough to access the terminal lugs. I unplugged the old element and plugged in the new element. I also replaced the old mounting screws w/new hardware and replaced one of the terminal lugs on a damaged wire. I went ahead and replaced the broiler element at the same time (also only 2 screws on the top of the oven) although there was no indication of a problem. The process was very easy although I caution non-electrically skilled people to insure the power is off at the breaker panel when performing this work and, if the electrical wires are damaged, seek qualified assistance to repair them. Read more...
Your Price 41.52
  In Stock
Delta Frame Surface Unit - 6 Inch
PartSelect Number PS11757480
Manufacturer Part Number WPY04100165
This is a delta frame surface unit, also known as coil element, for a stove, range, or oven. It is a 6-inch surface burner with a reinforced delta frame that carries 1250 watts and 240 volts. The burner has four turns and is compatible with many electric ranges. The center medallion is black in color. The burner provides heat to your cooking area to cook your food items. If your burner is not heating properly, you may need to replace it. Be sure to disconnect power to the appliance before completing this repair.
Fixes these symptoms
Installation Instructions
Donna from Charlotte, NC
Cooktop was looking old and worn though there was no working problem.
All of the "old" pieces were very easily removed and replaced with the new pieces. The update looks terrific and works just fine! Read more...
Your Price 82.84
  In Stock
Burner Surface Element - 8 Inch
★★★★★
★★★★★
(1)
PartSelect Number PS11740818
Manufacturer Part Number WP3177565
This is a burner surface element and is 8 inches in diameter and 2600 watts. The burner surface element functions as a cooking area on the cooktop of the range. The purpose of this part is to supply heat to the cooking area. This is a 5 turn coiled surafce element that features looped terminal ends. The element is sold individually. Before installing, make sure to unplug the cooktop and to allow enough time for your current element to cool down. The most common reason for needing a new element is if your current one will not heat.
Fixes these symptoms
Installation Instructions
ron from WALNUT CREEK, CA
Element has reached its life expectancy.
The new element has a manufacturing defect. This problem was immediately rectified by their salesperson Mary. Another burner element is on its way thanks to the professional and personal help from Mary. Read more...
Your Price 49.88
  In Stock
Igniter Switch
PartSelect Number PS11742372
Manufacturer Part Number WP4330739
This is an igniter switch for a gas oven, stove, or range. This part is sold individually. When the gas burner valve knob is pressed and rotated, the igniter switch creates a spark that ignites the gas and starts the burner. Without this switch, the burner cannot ignite. This part is approximately 1.5 inches tall and wide. It is made of plastic, and is white in color. This part is sourced directly from the original manufacturer. Be sure to disconnect power to your oven before completing this repair.
Your Price 11.60
  In Stock
Surface Burner Plug-In Block Kit
★★★★★
★★★★★
(14)
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms

Appliance Type

Popular Roper Cooktop Models

Below are the most popular Roper Cooktop models we have. Enter your model number in the search box to find your model.