Lawn Equipment Parts
How to Fix a Samsung Dishwasher That Won’t Start
Click a Part Below to Start Your Repair:Door Latch Or Door Latch Switch Timer Or Electronic Control Selector Switch Motor Start Relay Thermal Fuse Drive Motor
About this repair:
- Rated as EASY
- 1817 repair stories
- 7 step by step videos
Door Latch Or Door Latch Switch
If your Samsung Dishwasher won’t start, the problem could be the door latch or door latch switches. The door latch assembly is used to hold the door closed during the cycle to prevent water from leaking and it also incorporates the door latch switches that supply power to the Samsung Dishwasher controls. If the door cannot close properly to activate the door latch switches or if the switches are defective, then the Samsung Dishwasher controls will not receive power and the Samsung Dishwasher will not start. Inspect the latch assembly including the switches.
How to test a Samsung Dishwasher door latch assembly with a multimeter:
- Disconnect your appliance from the power source before beginning.
- Begin by removing the inner door panel to gain access to the door latch assembly. It is usually found at the top of the door. Once you have located it, verify that the door catch activates the door latch switches by inserting the catch into the assembly.
- If the switches are being activated mechanically, remove the switches to check them for continuity. Using a multimeter on Rx1, touch the probes to the switch’s terminals. This should produce a reading of zero or nearly zero.
- If you receive a different reading, you will need a replacement door latch assembly.
Timer Or Electronic Control
If you have determined that the door latch assembly is operating properly and your Samsung Dishwasher still won’t start, the next step would be to look at the timer or electronic control. The first step of the Samsung Dishwasher cycle is normally a drain function to remove any standing water in the tub. If you do not hear the drain pump motor running, then you should look at the timer or electronic control as a possible cause. On manual timer models, the timer is used to supply power to the pump motor, water inlet valve, heater circuit and drain pump motor at the proper sequence in the cycle. The timer uses a series of electrical contacts that are driven by a small motor all of which are encased in the timer housing.
How to test a Samsung Dishwasher timer with a multimeter:
- Disconnect your appliance from the power source.
- Locate and remove the timer. It will most likely be found in the control panel, but it is also often found behind the lower kick plate.
- Some timers may have multiple sets of contacts/wires, if this is true for your model, you will need to refer to your wiring diagram to determine which contacts to test.
- Set your multimeter to Rx1000 and touch the contacts with the probes. Most functioning timers will fall in the range of 2000-3500 ohms of resistance, but this varies between models. Refer to your owner's manual to determine what reading your test should produce.
- If your test results differ from the manufacturer's recommendations, you will need a replacement timer.
The selector switch on a Samsung Dishwasher is used to select different options for the individual cycles, such as heated dry and heated wash cycles. Depending on the model involved, the switch may be used in the motor or fill circuit and could cause a Samsung Dishwasher to not start if it were defective or if the selector buttons were not fully depressed. Check to ensure that the switch is properly depressed before attempting any disassembly. The contacts of the selector switch can be checked for continuity with a multimeter using the schematic diagram as a guide.
How to test a Samsung Dishwasher selector switch with a multimeter:
- Begin by disconnecting your appliance from the power source.
- Remove the inner door panel of your Samsung Dishwasher in order to locate the selector switch. It most likely will be found on the control panel. Once you have located it, ensure that the switch is properly depressed. If it is, remove it from the appliance in order to test it.
- Using a multimeter set to Rx1, touch the probes to the terminals of the switch, you will need to test each button individually. This should produce a reading of infinity. Next, with the probes still on the terminals, press in on the button of the terminals you are testing. This should change your reading to zero. Repeat this test for all other buttons.
- If any of your readings do not match the results above, you will need a replacement selector switch.
Motor Start Relay
Some models of Samsung Dishwashers use a start relay on the main pump motor. The start relay is used to supply power to the motor start windings until the motor is running and has a moving plunger inside that operates a set of contacts. If your Samsung Dishwasher won’t start and you have verified that you are getting power from the control circuit to the motor, then the motor start relay may be defective.
How to test a Samsung Dishwasher motor start relay:
- Ensure that you have unplugged your Samsung Dishwasher before beginning.
- The motor start relay is normally located next to the pump. Remove the lower access panel of your Samsung Dishwasher in order to locate the motor start relay. Once you have found it, remove it in order to test it.
- After referring to your wiring diagram, set your multimeter to Rx1 and begin by testing the coil portion of the relay for continuity. This test should produce a reading of zero or nearly zero. Next, you will need to manually activate the relay by turning it upside down and allowing the plunger to drop. Once it is activated, touch the probes to the terminals of the relay. This test should also produce a reading of zero or nearly zero.
- If your test results differ from those above, you will need a replacement motor start relay.
Some models of electronic controlled Samsung Dishwashers use a thermal fuse to protest the control board. The thermal fuse is normally located on the top side of the circuit board assembly with two wires attached to it. When the thermal fuse fails, the control board will not receive power and the Samsung Dishwasher will not start.
How to test a Samsung Dishwasher thermal fuse with a multimeter:
- Unplug your appliance before beginning this test, you will be handling electrical components.
- Remove the inner door of your Samsung Dishwasher in order to access the control panel. The thermal fuse will be attached to the control panel by 2 wires, carefully disconnect these wires and remove the thermal fuse in order to test it.
- With a multimeter set to Rx1, touch the fuse’s contacts with the probes. You are testing for continuity and should receive a reading of zero or nearly zero.
- If you do not receive this reading, you will need a replacement thermal fuse.
A Samsung Dishwasher’s drive motor is the part that circulates the water to wash the items inside. Electrical power to operate the drive motor is supplied through the timer, or the electronic control, in conjunction with a start relay. If the Samsung Dishwasher won’t start after the start relay sends power to the motor, this could indicate that the drive motor is defective. You may also hear a loud, humming noise coming from the motor – this could indicate a seized motor, which would need to be replaced.
How to test a Samsung Dishwasher drive motor with a multimeter:
- Before starting, ensure that you have disconnected your Samsung Dishwasher from the power source.
- Remove the lower access panel of your appliance in order to locate the drive motor. Once you have located it, carefully disconnect the wires attached to it and remove it in order to test it for continuity.
- With the motor removed from the appliance, set your multimeter to Rx1 and touch the probes to the motor’s terminals. A functional drive motor will produce a reading of zero or nearly zero. Next, test the ground connection by moving one of the probes to the bare metal housing of the motor. This test should not produce any reading.
- If either of your tests produces different readings, you will need a replacement drive motor.
More Repair Parts
Still not sure which part is broken? We can offer you custom troubleshooting help if you search with your model number.