Refrigerator Springs and Shock Absorbers

Shop By Brand

Popular Refrigerator Springs and Shock Absorbers

Your Price
$10.04
  In Stock
SPRING
★★★★★
★★★★★
(43)
PartSelect Number PS3630729
Manufacturer Part Number MHY62044103
This spring is located on the mullion, or door flap, of your fridge. This spring is sourced from the genuine OEM manufacturer for various refrigerator models. It measures about 1.5 inches in total length, and is made entirely out of metal.
Fixes these symptoms
Installation Instructions
Claudio from YONKERS, NY
Door flap spring
Insert the top first and then twist to insert bottom Read more...
Your Price
$6.24
  In Stock
Recess Door Spring
★★★★★
★★★★★
(12)
PartSelect Number PS285013
Manufacturer Part Number WR02X10585
This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find the spring in the water dispenser assembly, behind the main control panel. If the dispenser lever is malfunctioning or the dispenser ice door is not closing, you may need to replace this door recess spring.
Fixes these symptoms
  • Door latch failure
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
Bill from Cleveland Heights, OH
flap to ice dispenser would not close
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.

The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier.
Read more...
Your Price
$15.04
  In Stock
French Spring
★★★★★
★★★★★
(19)
PartSelect Number PS2322785
Manufacturer Part Number WR02X12650
Sold individually.
Fixes these symptoms
Installation Instructions
Barbara from TREMONT, IL
The French swing part of the door would not go back where it needed to. I had to put it back in place with my hand.
I just replaced the broken spring and the little plastic cylinder that goes over the end of one part of the spring. I placed the plastic part on first and slid it in place, then had to bed the other end of the spring a little bit to place it in the hole. But once it went in, the door worked perfectly. And I'm a 70 yr old woman. So if I can do it, anyone can. Read more...
Your Price
$10.04
  In Stock
Refrigerator Spring
★★★★★
★★★★★
(6)
PartSelect Number PS6012670
Manufacturer Part Number MHY62044106
This is a replacement door mullion spring for your refrigerator. The door mullion is the flap that allows the doors on your French-door style refrigerator to close. The spring allows the mullion to fit into a latch on the refrigerator door frame, and lets the door stay closed properly. If you have a damaged spring, your door will not close properly. This part is sold individually.
Fixes these symptoms
Installation Instructions
Charles R from FAIRFAX, VA
Spring on door closer broke
Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works. Read more...
Your Price
$11.56
  In Stock
Torsion-Fit Spring
★★★★★
★★★★★
(1)
PartSelect Number PS2374786
Manufacturer Part Number WR49X10233
This part is the replacement torsion-fit spring for your refrigerator. It is made of metal and is sold individually. The torsion-fit spring provides tension to return the ice funnel back to its normal position after it dispenses ice. If your refrigerator is not dispensing ice or water properly, you may need to replace the torsion-fit spring. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
carl from vacaville, CA
ice and water would not dispense at door
first I snapped out control face plate on outside of door. removed the screws for each part,and unplugged the wires at the connectors, replaced new parts and plugged in connectors to new circuit board.I decided to replace the board,switch and solenoid all at the same time, not knowing which part was bad.I have to say it was well worth it! it works better than when it was new!!!! It was a lot easier than I thought it was going to be. Read more...
Your Price
$7.55
  In Stock
Spring,Lever
★★★★★
★★★★★
(1)
PartSelect Number PS3524589
Manufacturer Part Number 4970JA3011K
Fixes these symptoms
Installation Instructions
walter from watertown, CT
your company does not answer phone because of virus. never got my spring part a hole in box, happens every something gets delivered from fed x send me my part will never buy from this company again.12-2-20
call me 860-417-2697 or e-mail when part is coming and answer phone or have option on line that did not get part nothing on line for that. Read more...
Your Price
$7.80
  In Stock
Ice Chute Door Return Spring
★★★★★
★★★★★
(1)
PartSelect Number PS2059882
Manufacturer Part Number 61004388
Sold Individually.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Matt from Green Bay, WI
Lower hinge (door closer) was worn out, so door wouldn't close on its own.
Simple. Removed all food and shelves from the door. Removed the top hinge, which allowed me to lift the door off the door closer. I layed it on the kitchen table on its front with the handle over the edge so it wouldn't cause a problem. Since I had it all apart I replaced both the top and bottom pieces of the door closer, and put a touch of grease on it. I then reassembled it in the reverse order. - The fountain spring and actuator pad were for a different problem with the fountain. It wouldn't shut off all the time because the actuator pad was getting stiff from time and use. I removed A/C power and turned off the water, then removed the front screws from the fountain cover. I then had easy access to the actuator pad, which only took a few minutes to replace. Careful when you pull the cover off, there are wires connected to it. Just don't forget to pull the plug out off the wall so you don't get killed! Read more...
Your Price
$6.24
  In Stock
SPRING HINGE MULLION
★★★★★
★★★★★
(1)
PartSelect Number PS6011724
Manufacturer Part Number WR01X11052
Fixes these symptoms
Your Price
$6.24
  In Stock
SPRING DEFLECTOR INT.
★★★★★
★★★★★
(4)
PartSelect Number PS1766053
Manufacturer Part Number WR02X11768
Installation Instructions
Jeffrey from LITTLETON, CO
plastic on auger was broken-wouldn't dispense ice
Excellent video on youtube showing how to replace the auger-Refrigerator and IceMaker Repair - Replacing the Auger Assembly (GE Part# WR17X11705).Very detailed video showing every aspect of this repair. There are many other videos showing this exact repair!! Read more...
Your Price
$7.11
  In Stock
SPRING- CH
★★★★★
★★★★★
(2)
PartSelect Number PS11738537
Manufacturer Part Number WP12565502
Fixes these symptoms
Installation Instructions
Paul from Baldwinsville, NY
Water / Ice dispenser broken
This repair was really easy. I first removed the water evaporator tray exposing 2 nuts and removed them with driver. Detach the dispenser faceplate and unplug the connections from the circuit board. Remove 2 more nuts holding the dispenser yoke paddle.

Remove the snap in paddle and replace with new part and spring. Complete assembly in reverse order. 10 minutes to complete repair.
Read more...

Brands