Pole Saw Seals and Gaskets

Pole Saw Intake Gasket This is a genuine manufacturer approved replacement part designed for use with edgers and trimmers. The purpose of this part is to act as a seal for the insulator. This item is made out of compound material and it is sold individually. To complete this repair you would need a screwdriver.

Pole Saw Carburetor Gasket This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. It is recommended to replace gaskets when servicing the motor to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.

Pole Saw Intake Gasket This replacement gasket-intake is an authentic OEM component. It is specially designed for use with Echo handheld lawn and garden equipment. This gasket is utilized to provide a tight seal between the insulator and the carburetor. Over time due to heat and regular wear, the material may begin to crack eventually requiring a replacement to maintain peak performance. Note, one durable composite material gasket is included. Check the diagrams of your model for the exact location and the correct installation of this component. To replace it, you will need a screwdriver to remove and resecure the carburetor and the intake manifold.

Pole Saw Intake Gasket Genuine OEM replacement part, this item is sold individually. This gasket acts as a seal to keep air and debris from entering the engine. Over time gaskets will compress and breakdown and then need replacement.

Pole Saw Intake Gasket This is a genuine OEM authorized replacement part used on Echo handheld lawn and garden equipment. It is made out of compound material and it is sold individually. This gasket acts as a seal between the heat dam and the cylinder head. Over time gaskets will compress and breakdown and then need replacement.

Pole Saw O-ring This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. The O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.

Pole Saw Intake Insulator This item is an authentic Echo replacement part that is OEM sourced to be used with trimmers, pruners, hedge trimmers, and edgers. The insulator is used to mount the carburetor to the cylinder assembly. This item is priced as a single item. Please note it may be necessary to inspect and possibly replace the gaskets when installing the insulator to ensure proper seals when the part is installed.

Pole Saw Oil Seal This oil seal is an OEM part that is used in trimmers, blowers, and edgers made by Shindaiwa and Echo. This item is a part of the small block assembly and is used to prevent oil leaks from between the crankshaft and the crankcase. The oil seal is priced individually, please note that two seals might be required.

Pole Saw O-ring This is an authentic manufacturer sourced replacement part designed for use with blowers/trimmers. It helps to provide an air tight seal for the carburetor. It is made out of rubber material and it is sold individually. To complete this repair you will need a screwdriver.

Pole Saw Gasket This Carburetor Gasket provides a tight seal between the carburetor and insulator. If broken, the engine will run lean due to excess air causing performance issues, and the part should be replaced. If the carburetor has to be taken off for any reason, the gasket should be replaced, as it is one-time use. Installation requires a screw driver and pliers, and is rated as "Easy".