This is a 2100 watt bake element for your oven or range. The element supplies heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. Simply remove oven racks to access the bake element. Use a Phillips screwdriver to remove the two screws that secure the element to the oven body. Electrical wires feature slip-on connectors for easy installation, but be sure to hold the wires forward so the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Element will not heat
Ask our experts a question about this part and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Susan
June 5, 2019
What is the size of this element. And are the connecters slide together (like a crimped slip on )
For model number C970-47121-3 Kenmore wall oven
Hello Susan, thank you for inquiring. This Bake Element is 14.75" from the front to the mounting bracket, and 14.25" wide. The connectors do not look like what you describe as 'crimp on element connectors'. We hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
George
March 5, 2018
I have a Frigidaire custom imperial oven. I've removed the screws holding the baking element, but something is keeping it from sliding out. It is loose but will only come out fraction of an inch before it is hung up.Thanks
For model number REG94GBK
Hi George,
Thank you for your question. Based on customer comments regarding the installation of the bake element, you will have to lift and wiggle the element out a bit to access the electrical wires still connected to it. Once the wires are removed, you can take the element out and install the new one. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Susan
June 6, 2019
Is this for 240 volt
For model number PS978772
Hello Susan, Thank you for the question. This element is Rated 2100 Watts at 240 Volts. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
October 16, 2021
Replaced oven heat element will not heat is there a reset button or what?
For model number TEF351EWC
Hello Robert, thank you for writing. There is no reset button. You may want to test or change out the Terminal Block part FIX471605. (see video). We hope this helps.
What are the dimensions of this part (ps978772)...and are the connecters "l' shaped no holes in metal "l"
For model number Kenmore C970 47121-3
Hello Susan, thank you for inquiring. This Bake Element is 14.75" from the front to the mounting bracket, and 14.25" wide. Very sorry but I am not sure what you mean by "I" connectors. The connectors on this element are push on, not screw on and do not have a hole. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Denise
October 12, 2021
What would make the bake element blow a hole in it? My sister in law was baking and the element blew a hole in it.
Hello Denise, Thank you for the question. It could have bene a defect in the element and caused a surge to short out the Element. In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Howard
April 4, 2018
Will this baking element fit in my oven.The present element is 13 inches wide by 19.5 long
For model number RBG94K
Hello Howard, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS474712. Good luck with the repair!
Was this helpful?
Thank you for voting!
David
October 13, 2022
Does this heating element fit my oven. My oven will not heat up to temperature.
For model number FEB556CESG
Hi David,
Thank you for your question. Yes, this would be the correct bake element for your range. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Chuck
January 27, 2023
If the lower heating element is bad will it affect the upper heating element.
For model number FEB24S5ABB
Hi Chuck,
Thank you for your question. When you use the bake function on the oven, both the bake and the broil element will cycle on and off to provide heat in the oven. If the oven is not heating correctly, you will need to check the elements, the temperature sensor, the electronic control board and the wiring between the parts. We have included some links that you may reference on how to check these parts. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
I have a 27 in. Kenmore wall oven needing a bottom element. Will this fit my oven?Thanks.
For model number C970-411727
Hello Sue and thanks for writing.
The model number you provided is not recognized. Please verify the number you provided us. If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part! It is possible that part #ps978772 might work with your unit; however, as we do not have your model number in our database we can not guarantee the fit. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Customer Repair Stories
Average Repair Rating: 4.8 / 5.0, 7 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven wasn't baking; broiler was OK.
1. Switched the oven power off. 2. Tried unscrewing the two screws in the rear of the oven but they were too tight. Used a power screw driver to unscrew the bottom element. 3. Pulled element out and disconnected the two wires. 4. Attached the two wires to the new bake element and fastened it with the two screws. 5. Switched the oven power on. 6. Tested the oven with good results!
Alexander from TEMPE, AZ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Baking heat element burned out
Removed oven racks removed 2 screws & pulled the element forward & disconnected the old element by wiggling the snap on connecters put in new element connected the snap on wires pushed it back in place & put both screws back in done in 10-15 minutes ??
Terry from BIG SPRING, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced the burned out bake element in my wall oven
first, I watched the video that partselect provides, then followed the instuctions that I learned from the video, I turned off the power to the appliance, removed the oven racks, removed the screws from the plate that held the oven rack in place and gently pulled it out far enough to remove the ends of the element from the electrical current wires, finished removing the burnt out element and replaced it with the new one from Partselect by repacing the new element ends on the electrical current wires and screwed it into place and replaced the racks, turned on the power and baked my pie. I am a 71 year old widow who was able to accomplish this with the good instructions provided by Partselect, this was the first time I have ever tried to do anything like this on my own.
Donna from Guide Rock, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
7 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
minimal/no heat
turned off main power; took a flash light, unscrewed existing element and disconnected it from the wiring; compared existing with new elements as the shipping label said "ABSOLUTELY NOTHING MAY BE RETURNED IF IT APPEARS THAT IT HAS BEEN INSTALLED"; it appeared to be close enough but not exact. Connected wiring to new element, shoved it back into the insultation, screwed in the element with the same screws. Viola' all worked as it should. I even set my oven on the "self clean" cycle which is 3 hours on high. Overall it was very easy.
First removed the two screws that hold the element in place.I then pulled the element out about three inches and disconnected the two wires. The new element was put in place and reconnected to the two wires.The two screws to hold the element in place wre put back in.Very easy.
Marie from Fairview Park, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element showed a hot spot prior to failing open.
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done!
James from Delaware, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
28 of 31 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
4.7
Filter By Rating:
5 Stars
4
4 Stars
2
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ronnie V - May 14, 2021
Verified Purchase
My wife of 51 years is happy. She can bake again.
The element was delivered quickly. It was easy to install. It works great. What else could you ask for?
★★★★★
★★★★★
James S - March 1, 2021
Verified Purchase
Easy repair
It was an easy repair even for those of us that are all thumbs. Unhook the old one and attach the wires to the new one.
★★★★★
★★★★★
RICHARD S - May 27, 2020
Verified Purchase
repair
Part was right one installed easily and worked well.
★★★★★
★★★★★
Jeffrey M - February 26, 2019
Verified Purchase
Easy fix
Part was exactly what we needed....took a little longer to get.
★★★★★
★★★★★
Jeff R - October 19, 2018
Verified Purchase
Good service
The correct parts was sent and was easily installed.
★★★★★
★★★★★
Rebecca T - May 31, 2018
Verified Purchase
Easy repair
Worked great, easy install
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS978772
Manufacturer Part Number: 318255101
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
